534704

German RepRap PRotos V2.0 Manual

5
Zoom out
Zoom in
Previous page
1/281
Next page
PRotos V2.0 3D Drucker Handbuch
Seite 5 /
Revision 352
Stand 23.12.201314:03
PRotos V2.0 3D Drucker Handbuch
© German RepRap GmbH 5 /
Abbildungsverzeichnis
1. PRotos V2.0 3D-Drucker ........................................................................................................... 13
3.1. Werkzeug ............................................................................................................................. 19
3.2. ©Arduino MEGA 2560 ............................................................................................................ 21
3.3. Bar Clamp ............................................................................................................................ 22
3.4. Endstop Holder ..................................................................................................................... 23
3.5. Extruder-Gegenlager .............................................................................................................. 24
3.6. Grundplatte-Lüfter ................................................................................................................. 25
3.7. Grundplatte-Mittelstück ......................................................................................................... 26
3.8. Grundplatte-Schrittmotor ....................................................................................................... 26
3.9. Linear Bearing Clamps ........................................................................................................... 27
3.10. Ramps v1.4 ......................................................................................................................... 27
3.11. X-Carriage .......................................................................................................................... 28
3.12. X-Carriage Belt Clamp .......................................................................................................... 28
3.13. X-Carriage Clamp ................................................................................................................ 29
3.14. X-Idler ................................................................................................................................ 30
3.15. X-Motor Mount ................................................................................................................... 31
3.16. X-Shaft Clamp ..................................................................................................................... 32
3.17. Gewindestangen .................................................................................................................. 33
3.18. Edelstahlstangen .................................................................................................................. 34
3.19. Pully Alu T2.5 ...................................................................................................................... 35
3.20. PET-Folie 230mm x 230mm .................................................................................................... 36
3.21. Kaptonband 5mm ................................................................................................................ 37
3.22. Kaptonband 50mm ............................................................................................................... 38
3.23. PET-Band 50mm .................................................................................................................. 39
3.24. Rahmen und 4 Maschinenfüße .............................................................................................. 41
3.25. Y-Opto-Endstophalter Teil 1 .................................................................................................. 42
3.26. Y-Opto-Endstophalter Teil 2 ................................................................................................. 42
3.27. Rahmen Gewindestangenmontage ......................................................................................... 43
3.28. Montage Elektronikhalter ..................................................................................................... 44
3.29. Abschluss der Rahmenmontage ............................................................................................. 45
3.30. Materialliste Y-Schlitten ........................................................................................................ 46
3.31. Detailansicht: Y-Riemenspanner und Y-Riemenklemme Montage Teil 1 ........................................ 47
3.32. Detailansicht: Y-Riemenspanner und Y-Riemenklemme Montage Teil 2 ......................................... 48
3.33. Spätere fertige Montage des Y-Riemenspanners, der Y-Riemenklemmen, Schrauben und
Unterlegscheiben ....................................................................................................................... 49
3.34. Führungswellen Abschluss .................................................................................................... 49
3.35. Materialliste Y-Achsen Schrittmotor ....................................................................................... 50
3.36. Y-Achsen Schrittmotor Montage ............................................................................................ 51
3.37. Zahnriemenführung Materialübersicht .................................................................................... 52
3.38. Zahnriemenführung Detailansicht Verschraubung ..................................................................... 53
3.39. Zahnriemenführung fertig montiert ........................................................................................ 54
3.40. Einspannung des Riemens in die Y-Riemenklemmen .................................................................. 55
3.41. Z-Achsen Führungsstangen Materialübersicht 1 ........................................................................ 56
3.42. Z-Achsen Führungsstangen Materialübersicht 2 ........................................................................ 57
3.43. Fertig montierte Teile: Motor, Kupplung und Gewindestange ...................................................... 58
3.44. Fertig montierte Teile: Motor, Kupplung, Gewindestange und Z-Achsen-Halterung ......................... 59
3.45. Z-Achsen-Halterung Fixierung .............................................................................................. 60
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for German RepRap PRotos V2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of German RepRap PRotos V2.0 in the language / languages: German as an attachment in your email.

The manual is 64,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info