522267
9
Zoom out
Zoom in
Previous page
1/29
Next page
offered by Busse-Yachtshop.com
14
15
EnglishEnglish
NAVIONICS ELECTRONIC CHARTS
The GEONAV includes a built-in world map that allows zoom-
ing from 4,096 down to 512NM. Additional cartography de-
tails relative to a specific area of navigation are available from
the CompactFlash™ cartridges storing NAVIONICS GOLD
CHARTS.
To display chart boundaries, press PAGE until the menu bar
appears, select SETUP, CHART BOUNDARIES, then select
ON/OFF to enable/disable the boundaries of the charts stored
in the cartridge. A small square will locate the area covered by
the cartridge installed.
Increasing/decreasing the chart range
Press the -ZOOM+ key.
Displaying depth and safety contours,
geographical names, spot soundings
and light sectors
Press PAGE to display the menu,
select SETUP and enable the
option desired (Depth Cont.,
Safety Cont., Spot Soundings,
Names or Light Sectors) by us-
ing the CURSOR key.
Converting depth values into the units
set
Press PAGE to display the menu,
select SETUP, DEPTH UNITS
and then set the unit desired to
meters, feet or fathoms.
The GEONAV will convert all the depth values in the unit
selected, making them appear like those reported in the offi-
cial nautical charts (see the figure).
NAVIONICS Electronic Charts
Diagnostic
DIAGNOSTIC
The GEONAV features a diagnostic program to verify its cor-
rect performance, once installed, and to detect problems that
may occur during the use of the unit.
To access the diagnostic program, keep pressed any key but
CLR, while pressing the PWR key.
The GEONAV will switch on and carry out automatically a
test of the whole system; as soon as the memory test is com-
pleted, the program will test the LCD, the CompactFlash™
card and the keyboard. Press ENTER to run one test, CLR to skip
to the next one. To exit from the keyboard test, press CLR
twice.
Once the keyboard test is completed, the diagnostic program
allows checking the messages received from the GPS through
the NMEA 0183 port. Hold the ENTER key pressed to freeze the
messages on the screen, then release it to keep on displaying
the new messages sent by the GPS. To test channel 2 (depth
sounder or wind instrument), press GOTO. Press CLR to quit.
After the keyboard, the diagnostic program will test the inter-
nal GPS (if available) and the backlight. Press ENTER to run
one test, CLR to skip to the next one.
Once terminated all tests, press ENTER to re-boot the unit.
WARNING: The internal memory can be cleared by pressing simultaneously the
PWR and CLR keys. This operation will delete all the settings stored in the GEONAV
and restore factory settings.
NOTE: In case of damaged cartridge or abnormal power spikes, the unit might lock,
requiring a power shutdown to restart. In that case, the unit can be turned off without
the need of detaching the power, by simply pressing the GOTO, PAGE and CLEAR
keys at the same time. This function is useful if the unit is panel mounted or flush
mounted and the power switch cannot be easily accessed.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geonav 6 SUNSHINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geonav 6 SUNSHINE in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info