702915
7
Zoom out
Zoom in
Previous page
1/44
Next page
7
GB
3 The Nicer Dicer Fusion in practical use
Insert the cutting top at an angle of 90° (vertically) to the cutting base in
the side slots provided. The cutting lid has an opening mechanism with 3
settings.
There are different pin blocks and a cutting stamp for the various blade
inserts to achieve the best possible cutting results.
There is an integrated pin block (A) in the cutting top. There are also two
detachable pin blocks (B) (large and small), which can be fixed in place
next to the integrated pin block.
They are fixed as follows:
There is a cross-shaped recess next to the integrated pin block. On the
back of each detachable pin block and the cutting stamp, there is a cross-
shaped mounting. Push the mounting on the pin block or cutting stamp
into the recess with gentle pressure until the block or stamp is fixed in
place and ready to use.
The automatic opening mechanism can be set by means of two pins (A) in
three positions.
Lock the protruding pins to achieve the required setting (B):
Setting 1 = pins not locked: no automatic lid opening
Setting 2 = one pin locked: slow automatic lid opening
Setting 3 = both pins locked: fast automatic lid opening
Use of the detachable pin block and cutting stamp:
Blade inserts with two different cutting surfaces (for explanation, see 3.1):
- Use of one cutting surface = integrated pin block sufces, no other insert required
- Use of both cutting surfaces = also use detachable pin block (small)
XXL blade with continuous cutting surface (for explanation, see 3.2)
- Detachable pin block (large) must also be used.
Blade insert for cutting into quarters/eighths (for explanation, see 3.3)
- Cutting stamp must also be used.
Note: The pin blocks and cutting stamp are required for the cutting process as they push the ingredients to be
cut continuously through the blades, thereby ensuring a clean cut.
A
B
B
A
3.1 Blade inserts with 2 different cutting surfaces
The blade inserts have 2 different cutting surfaces, referred to as position 1
and 2 in these Instructions for Use (see figure). Food can be cut on both sur-
faces and it is possible to cut two different ingredients at the same time. The
following should be noted in this connection:
If one of the ingredients to be cut is harder than the other, place the
harder one in position 1 (greater leverage).
If one of the ingredients to be cut is larger than the other, place it in
position 2 (longer lever travel).
Position 1
Position 2
Figure:
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Genius Nicer Dicer Fusion at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Genius Nicer Dicer Fusion in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Genius Nicer Dicer Fusion

Genius Nicer Dicer Fusion User Manual - German - 20 pages

Genius Nicer Dicer Fusion Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info