502912

General Electric Side by Side 25 Manual

35
Zoom out
Zoom in
Previous page
1/280
Next page
35
Installing the Water Line
For Australian and New Zealand installation, read these instructions completely and carefully.
IMPORTANT: Government legislation and Codes
in most States and Territories of Australia
require installation by a licensed plumber.
The installation must conform to Australian
Standard AS 3500.1 Water supply.
Water hammer (water banging in the pipes)
in house plumbing can cause damage to the
refrigerator parts and lead to water leakage
or flooding. Call a qualified plumber to correct
water hammer before installing the water supply
line to the refrigerator.
To prevent burns and refrigerator damage, do not
hook up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch
is set to the O position.
Do not install the icemaker tubing in areas where
the temperatures fall below freezing.
Before You Begin
For models fitted with an icemaker, a water supply
kit (containing flexible tubing and fittings) is supplied
with the refrigerator.
The water pressure must be between 138 and
827 kPa on models without a water filter fitted
and between 275 and 827 kPa on models with
a water filter fitted.
Turn Off the water and open a low tap to drain
the water from the pipe.
Complying with the plumbing codes, install a suitable
branch fitting (not supplied) to the cold water supply.
Extend the branch to a suitable location adjacent
to the refrigerator when it is located in its operating
position. Terminate the branch with a shutoff valve
(not supplied).
IMPORTANT: The shut-off valve should be accessible
(such as in an adjacent cupboard, as close to the wall
as possible) when the refrigerator is in its normal
operating position.
If your water supply pressure is higher than 690 kPa
during the day (if so, it may reach higher levels
at night), install a suitable Pressure limiting valve
(not supplied), after the shut-off valve, making sure
the “flow arrows” on the body of the device face
the same direction as the water flow.
If necessary, assemble a suitable fitting (not supplied)
to the up-stream end of the shutoff valve (or pressure
limiting valve) for attachment of the fitting supplied
with the water supply kit.
NOTE: PTFE tape should be used for a water tight seal
when assembling all the above fittings.
Do not turn the water supply On at this time.
Shut Off the Main Water Supply
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric Side by Side 25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric Side by Side 25 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of General Electric Side by Side 25

General Electric Side by Side 25 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info