502986
5
Zoom out
Zoom in
Previous page
1/24
Next page
Safety Instructions
Operating Instructions
Care and Cleaning
Troubleshooting Tips Consumer Support
Using the oven controls. GEAppliances.com
Lower Oven Control (on some models)
OVEN TEMP Knob
Turn this knob to
the temperature
setting you want.
The OVEN CYCLE light glows until the oven reaches your selected
temperature, then goes off and on with the oven element(s) during
cooking.
5
Throughout this manual, features and appearance may vary from your model.
Upper Oven Control, Clock and Timer Features and Settings
BAKE Pad
Touch this pad to select the bake function.
BAKE Light
Flashes while in edit mode—you can change the
oven temperature at this point. Glows when the
oven is in bake mode.
BROIL HI/LO Pad
Touch this pad to select the broil function.
BROIL Light
Flashes while in edit mode—you can switch
from HI to LO BROIL at this point. Glows when
the oven is in broil mode.
Display
Shows the operations you have selected,
the time of day and the cooking status.
COOKING TIME Pad
Touch this pad and then touch the + or pad
to set the amount of time you want your food to
cook. The oven will shut off when the cooking
time has run out.
DELAY START Pad
Use along with the COOKING TIME or
SELF CLEAN pad to set the oven to start and stop
automatically at a time you set.
OVEN LIGHT ON/OFF Pad
Touch this pad to turn the oven light on
or off.
TIMER/CLOCK Pad
Touch this pad to select the timer feature. Then
touch + and pads to adjust time.
To set the clock, touch this pad twice and hold 3
seconds and then touch the + and pads. The
time of day will flash in the display when the
oven is first turned on.
START Pad
Must be touched to start any cooking function.
– Pad
Short taps to this pad will decrease the time
or temperature by small amounts. Touch
and hold the pad to decrease the time or
temperature by larger amounts.
+ Pad
Short taps to this pad will increase the time
or temperature by small amounts. Touch
and hold the pad to increase the time or
temperature by larger amounts.
CLEAR/OFF Pad
Touch this pad to cancel ALL oven operations
except the clock and timer.
SELF CLEAN Pad (on some models)
Touch this pad to select the self-cleaning
function. See the Using the self-cleaning oven
section.
CLEAN Light
Flashes while in edit mode—you can change the
length of time for the self-clean cycle at this
point. Glows when the oven is in the self-clean
cycle. After the self-clean cycle, the light will turn
off. Unlatch the door.
If “F– and a number or letter” flash in the display and the oven
control signals, this indicates a function error code.
Touch the CLEAR/OFF pad. Allow the oven to cool for one hour.
Put the oven back into operation.
If function error code repeats, disconnect power to the oven and
call for service.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric JRP20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric JRP20 in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info