646570

General Electric GFDS175 Manual

7
Zoom out
Zoom in
Previous page
1/44
Next page
GEAppliances.com
10
Ext Tumble/Wrinkle Care
Minimizes wrinkles by adding approximately 60
minutes of no-heat tumbling after clothes are
dry. The beeper will sound every five minutes as a
reminder to remove the clothes.
The estimated time remaining display will show
“0:00”.
The extended tumble time does not get added to
the cycle time on the display.
11
Damp Alert
This option causes the dryer to beep when clothes
have dried to a damp level. Remove items that you
wish to hang dry. The Damp Alert will only beep
when this option is selected, and the dryer will
continue to dry.
Removing clothes and hanging them when they are
damp can reduce the need to iron some items.
Volume
Alerts you that the cycle is complete. The beeper
will continue to sound every minute for the next 5
minutes, until the clothes have been removed. The
clothes should be removed when the beeper goes
off so wrinkles don’t set in.
Press Volume to select low, medium or high volume,
or to turn the beeper off.
To turn on or off the sounds the buttons make
when pressed, press and hold the Volume button
for 3 seconds.
Lock Control
You can lock the controls to prevent any
selections from being made. Or you can lock
or unlock the controls after you have started a
cycle.
Children cannot accidentally start the dryer by
touching buttons with this option selected.
To lock the dryer, press and hold the Lock
Control button for 3 seconds.
To unlock the dryer controls, press and hold the
Lock Control button for 3 seconds.
A sound is made to indicate the lock/unlock
status.
The indicator light above the button will
illuminate when the controls are locked.
NOTE: The Power button can still be used when
the machine is locked.
12
13
14
Clean Filter Message
This message represents only a reminder and does
not always appear when the filter needs cleaning.
The filter should be cleaned after every drying cycle
is complete.
This message will disappear after the Start/
Pause button is pressed. Even though you may
have already cleaned the filter (before or after the
Power button has been pressed), the “Clean Filter”
message will still be displayed until the Start/Pause
button is activated.
15
Display
Displays the approximate time remaining until
the end of the cycle.
As the cycle begins, you will see an initial
approximate total cycle time in the display.
Then lights will “race” in the display. This means
the dryer is continuously monitoring the amount
of moisture in the load. The lights will continue
until the dryer senses a low level of moisture in
the load. At that point, the dryer will calculate
and display the approximate time remaining.
My Cycle (on some models)
Set up your favorite combination of settings and
save them here for one touch recall. These custom
settings can be set while a cycle is in progress.
To store a My Cycle combination of settings:
1. Select your drying cycle.
2. Change Temp and Level settings to fit your
needs.
3. Select any drying options you want.
4. Press and hold the My Cycle button for 3
seconds to store your selection. A beep will
sound and the button will light up.
To recall your stored My Cycle combination:
Press the My Cycle button before drying a load.
To change your stored My Cycle combination:
Repeat steps 1–4.
16
My
Cycle
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric GFDS175 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric GFDS175 in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info