646523

General Electric DDG7980M Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
PROBLEM
POSSIBLE CAUSE AND REMEDY
SHWNKAGE,
●
Rela~tion
shrin~ge
can
occur
in
hit
fabrics
that
have
been improperly stretched
KNITS and elongated by the manufacturer. When this occurs, garment maybe pressed back into
shape
afir
each wash and dry cycle.
s
Progressive or delayed shrinkage
is caused when starch or sizing (in some fabrics) is
gradually removed by laundering. Maybe noticed in older garments that have been
laundered many times without previous shrinkage. Treat as for
Rektion
Shrinkage above.
●
Shrinkage caused by overheating
occurs in certain knit fabrics that have been
heat-
shaped. When washing, drying or ironing tem~ratures exceed the temperatures used to
shape set, shrinkage may occur. This cannot be corrected, but it can be prevented by
washing in cold or warm water; drying on low heat.
WNNKLINGIN
s
Leaving clothes in dryer after tumbling stops. Remove clothes promptly and hang
PERMANENT PRESS
them immediately.
AND “NO-IRON”
ITEMS
●
TM
many items in dryer.
Dry
only one washer load at a time. Do not combine loads.
●
Too few items in dryer. If drying only one article, add two or more similar articles, even
ifd~,
to insure proper tumbling.
●
Improper loads. Avoid laundering heavy Permanent Press items, such as work clothes,
with lighter Permanent Press items, such as shirts or blouses. Do not wash or dry
Permanent Press with regular laundry.
Q
Too many clothes in washer. Items must have room to move freely. Permanent Press
loads should always be smaller than regular loads..
.no
more than medium loads.
●
Use of incorrect wash and dry cycles. Use Permanent Press Wash Cycle which provides
a cool-down rinse to minimize
wrin~ing.
Also, use Permanent Press Dry Cycle.
●
Incorrect water level. Use large water level for medium load; medium level or
halffiil
for small load.
Q
Washing
repeatily
in too hot water. Wash in cool or warm
water with plenty
ofdekrgent.
11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric DDG7980M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric DDG7980M in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info