Manual General Electric CFCP1 (page 22 of 136) (English, French, Spanish)

503063

Zoom out

Zoom in

1/136

CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE (cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the

end of the tubing coming from the house cold

water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to

the tubing.

If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator, as

far as possible. While holding the tubing,

tighten the fitting.

If you are using GE SmartConnect

™

tubing,

insert the molded end of the tubing into the

refrigerator connection, at the back of the

refrigerator, and tighten the compression nut

until it is hand tight. Then tighten one

additional turn with a wrench. Overtightening

may cause leaks.

Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open

the clamp.

One of the illustrations below will look like the

connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

Installation Instructions

1/4” Tubing

Tubing Clamp

1/4”

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

TURN ON THE WATER SUPPLY

(icemaker and dispenser models)

Turn the water on at the shut-off valve (house water

supply) and check for any leaks.

PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the

refrigerator, make sure the icemaker power switch is set

to the O (off) position.

See the grounding information attached to the power

cord.

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location. Make sure the

back side of the refrigerator engages the anti-tip

bracket properly. The anti-tip floor bracket should line

up with the cutout in the back bottom of the

refrigerator, and fit through the cutout when the

refrigerator is pushed into position. (Refer to page 18,

Step 2A for more information.)

1/4” Copper

Tubing

1/4”

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

Tubing

Clamp

LEVEL THE REFRIGERATOR

Turn the front roller adjusting

screws clockwise to raise the

refrigerator, counterclockwise

to lower it. Use a 3/8″ hex

wrench with extension, or an

adjustable wrench.

To adjust the rollers on 21

‘ Counter Depth models:

These models also have rear adjustable rollers

so you can align the refrigerator with your kitchen

cabinets. Use a 3/8″ hex wrench with extension to turn

the screws for the rear rollers—clockwise to raise the

refrigerator, counterclockwise to lower it.

Roller adjusting screws

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of General Electric CFCP1 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 5,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

General Electric CFCP1 Manual

Product: