Manual Gemini XGA-5000 (page 12 of 23) (English, German, French, Spanish)

503427

Zoom out

Zoom in

1/23

eiligen Eingangssignals ist. Die folgenden Hinweise set-

zen die Verwendung von 8 Ohm oder 4 Ohm Lautspre-

chern oder Kombinationen mit ähnlichen Leistungswerten

voraus.

1. With the power off, set the operation mode switch (11)

to the stereo position. When the power is on, the bridge

led (18) on the front panel will not light. If this led illumi-

nates, you have the switch in the wrong position. Correct

before continuing.

1. Con la unidad apagada, seleccionar con el selector de

mododeoperación(11),enposiciónestéreo.Cuandose

haya encendido, el LED de modo puente(18) en el panel

frontalnoseiluminará.SiesteLEDseilumina,ustedtiene

elinterruptorenlaposiciónequivocada.Corrijaantesde

continuar.

1.Avecl’amplicateuréteint(Off),positionnezlecommu-

tateurdemodedefonctionnement(11)surstéréo.Enral-

lumantl’amplicateur(On),laLEDbridge(18)-situéeen

faceavant-doitêtreéteinte.Sicelle-ciresteallumée,vous

avezsélectionnélemauvaismodedefonctionnement.Ré-

pétez l’opération en sélectionnant le mode defonction-

nementadéquatavantdepoursuivre.

1. Im ausgeschalteten Zustand schalten Sie den Betrieb-

smodus (11) auf stereo. Eingeschaltet zeigt die Bridge LED

(18) an, wenn Sie den Schalter in der falschen Position ha-

ben. Korrigieren Sie dies vor dem Fortfahren.

2. With the power off, connect your input cables to the

channel1and2inputsusingeithertheXLRinputjacks(4,

5),1/4”trsinputjacks(6,7)ortheRCAinputjacks(8,9)of

each channel. The other channel 1 and channel 2 inputs can

beusedtolinktoanadditionalamplier.

2. Con la unidad apagada, conecte sus cables de entrada

en los canales de entrada 1 y 2 usando para ambos los

conectores XLR de entrada (4,5), los Jack de entrada TRS

¼” (6,7), o el RCA (8,9) para cada canal. Las otras entradas

del canal 1 y el canal 2 se pueden utilizar para enlazar otro

amplicadoradicional.

2. Avec l’amplicateur éteint (Off), branchez vos cordons

audioauxcanaux1&2enutilisantlesentréesXLR(4,5),

Jack6.35mm(6,7),ouRCA(8,9).Lesentréesnonutilisées

peuventalorsserviràrelierlesentréesdecetamplicateur

àunautreamplicateuralimentéparlemêmesignalaudio

(Chainlink).

2. Im ausgeschalteten Zustand schließen Sie Ihre Sound-

quelleandieXLREingänge(4,5),6,35mmKlinkeneingänge

(6, 7) oder Cincheingänge von Kanal 1 und 2 an. Die übrigen

Eingänge von Kanal 1 und 2 können verwendet werden, um

einenweiterenVerstärkerzuBetreiben.

3. Connect the loudspeakers to the channel 1 and channel

2 speaker outputs (12, 13). The total speaker load must be

at least 4 ohms per channel. If you try to operate at a lower

impedance,theamplierwillgointoprotectionmodeand

stop operation until you correct the load conditions.

3. Conectar los altavoces a las salidas de altavoces del ca-

nal1ycanal2(12,13).Lacargatotaldebesercomomínimo

de 4 ohm por canal. Si trata de operar con una impedancia

másbaja,elamplicadorsecolocaráenmododeprotec-

ciónydejarádefuncionarhastaquecorrijalascondiciones

de carga.

3. Connectez les enceintes aux canaux 1 & 2 via les sor-

ties enceintes (12, 13). L’impédance totale des enceintes

nepeutêtreinférieureà4Ohms.Sivoustentez-malgré

tout-uneimpédancemoindre,l’amplicateursemettraau-

tomatiquementenmodeprotection&cesseradefonction-

nerjusqu’àmodicationdel’installation.

3. Schließen Sie die Lautsprecher an die Ausgänge von Ka-

nal 1 und 2 an (12, 13). Die gesamte Lautsprecherlast muss

mindestens4OhmjeKanalbetragen.WennSiedenBetrieb

miteinerniedrigerenImpedanzversuchen,sowirdderVer-

stärker in den Protection-Modus schalten und den Dienst

verweigern, bis Sie die Last korrigieren.

4. With the level controls (21, 22) of both channels set to

zero (fully counterclockwise), turn the power switch (15) on.

With the level controls of your mixer or other input device

turnedallthewaydown,turntheamplierlevelcontrolsup

around3/4(or75%)fordesiredloudnessfromyourspeak-

ers.Note, when the clipled(19) lights, thereis distortion

presentin the amplier’s output section. If a clip led (19)

remainsonorashesrepeatedly,reducethesignallevelby

lowering the input level control for the channel that is clip-

ping or reduce the level at the source.

4.Con los controles de nivel (21,22) de ambos canales a

≤ (75% de la potencia del amplicador), en primer lugar

conectar la mesa de mezclas u otro dispositivo de entrada

yluegoencenderelamplicadorutilizandoelinterruptorde

encendido(15).Después,conloscontrolesdeniveldesu

mesa de mezclas u otro dispositivo de entrada nivelar el

audioandealcanzarlos0decibeliosenlosindicadores

delamesademezclas.Nota,cuandoelLEDdeClip(19)

se enciende, hay una distorsión presente en la salida del

amplicador.SielLEDdeClip(19)sigueencendidoopar-

padea repetidamente, reducir el nivel de la señal mediante

la reducción del nivel de entrada del control por canal o

reducir el nivel de origen.

4. Avec les potentiomètres(21, 22) en position 3/4 (75%

de la puissance de l’amplicateur), mettez d’abord vos

sources & console de mixage sous tension et allumez

l’amplicateur(On)àl’aidedel’interrupteurPower(15)en

dernier ressort. Puis avec les potentiomètres de volume

devotreconsoledemixageet/oudevossourcesréglezle

niveauaudiodefaçonàatteindrele0dBsurlesvu-mètres

devotreconsoledemixage.NotezquesilesLEDsdeclip

(19)s’allument, cela indique laprésence de distorsion en

sortiedel’amplicateur.SilesLEDsdeclip(19)restentcon-

stammentallumées,réduisezleniveaud’entréedelavoie

oudes2voiessicelaestnécessaireouréduisezlevolume

de la console de mixage ou de la source.

4. Mit den Lautstärkedrehreglern (21, 22) beider Kanäle auf

Nullstellung(vollständiggegenUhrzeigersinn),schaltenSie

denNetzschalter(15)ein.RegelnSiezuerstdieLautstärke

IhrerSoundquellefallsmöglichaufeinnormalesLine-Level

(0dB).DannregelnSiedieLautstärkedesVerstärkerssoweit

nach oben, bis die gewünschte maximale Lautstärke Ihrer

Lautsprecher erreicht ist. Wenn die Clip LED (19) leuchtet

Connections and System Control

ConexionesyControldesistema•Connexions&Utilisation•AnschlüsseundSystemeinstellungen

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gemini XGA-5000 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gemini XGA-5000 Manual

Product: