479884
8
Zoom out
Zoom in
Previous page
1/8
Next page
PAGE 14 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 15
13.0 -
13.1 - CONNECTIONS AND POSITIONING
13.2 - SENSOR ADJUSTMENT
Insert the WHITE connector
.
In case you don’t want to activate the diagnostic procedure, t
:
.
ULTRASONIC VOLUMETRIC PROTECTION
in the the “W” socket on the control unit.
Insert the RED connector in the “R” socket on the control unit.
Install the transducers of the ultrasonic sensors in the uppermost part of the windscreen internal
pillars, away from the aeration inlets and orient them towards the center of the rear window
o check sensitivity level proceed as
follows
With the alarm system disarmed, roll down the front window about 20 cm.
Adjust trimmer at a medium setting.
Close all doors, bonnet and boot and arm the system.
During the system inhibit arming time introduce an object in the cabin through the window and
move it around; the status LED will turn off to signal a presence.
If sensitity lelvel is too high or too low, readjust the trimmer and repeat the above procedure
!
!
!
!
!
To activate procedure proceed as follows:
system .
Push and keep pushed the or s
LED .
system
e.
2” while by activating any other device, at
every receiving of alarm or signals from electrical connections (i.e. hood button), one turn signal
flashing and one acoustic signal will be sound
LED .
.
!
!
!
!
!
Switch-off power supply
the status LED push-button hort-circuit the RED and BLACK wires
of the 2-way connector
Switch the on; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times
By opening a vehicle's door, the siren will be activated for
Release the state button or remove the short circuit, previously created
One turn signal flashing and one acoustic signal will indicate the end of diagnostic procedure!
14.0 - DIAGNOSTIC
By activating the diagnostic procedure, the system returns to the Factory default setting
This procedure must therefore only be used in case of need, before programming the
system or
.
changing the pin-code.
!
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT
15.0 - WARRANTY CONDITIONS
This
.
product is guaranteed to be free from manufacturing defects for a period of 24 months from the
installation date shown on this warranty, in compliance with the Directive 1999/44/CE.
Please fill-in entirely the guarantee certificate included in this booklet and do NOT REMOVE the
guarantee label from the device.
The warranty will become void if labels are missing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The guarantee is valid exclusively at authorized Gemini TechnologiesS.p.A. Service Centers.
The manufacturer declines any responsibility for eventual malfunctions of the device or any damage
to the vehicle electrical system due to improper installation, use or tampering.
This alarm system is solely intended to be a theft-deterrent device
16.0 - TECHNICAL SPECIFICATIONS
Power supply 863 - 862 - 861
Power supply 863/24 - 862/24
Current absorption @ 12Vdc with system armed and LED flashing
Working range temperature
Turn signals relay contact capacity
Engine immobiliser relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
Additional siren output current capacity
12 Vdc
24 Vdc
15 mA
From -30°C a +70°Cto
8 A at 20°C
30 sec.
8 A at 20°C
10 mA
5A
17.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
The present device does not fall within the scope of Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE) as specified in art. 2.1 of L.D. no. 151 of 25/07/2005.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 863 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 863 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 863

Gemini 863 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info