479883
6
Zoom out
Zoom in
Previous page
1/8
Next page
PAGE 10 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 11
9.0 -
In this chapter various functions of the system are concisely described; for programming please follow
the instruction given in paragraph “SYSTEM PROGRAMMING”.
This function activates acoustic signals during system arming (2) and disarming (3).
According to the programming, this function allows to:
Press the “panic button” of radio control in order to activate the siren for 30” (remote controlled
panic alarm).
Being the system armed, press the “panic button” of radio control in order to activate for few
seconds the siren and the turn signals (car finder).
This function activates the system anytime a voltage sudden change in the vehicle's electrical circuit is
occurring.
B current
.
This function allows vehicle’s protection in case the user disarms accidentally the system.
Thus, the system will be automatically rearmed after 35”, if no intervention on the vehicle is done (i.e.
door opening, engine start).
.
Function that allows to have the system active 35” after the engine switching “OFF”
.
Function that allows to select the CDL closure time.
This function allows activating the comfort control (window closing) when the system is armed.
This function activates twice the opening control and it is used on vehicles with diversified opening.
This function, once connected, can activate the supplementary siren or open the trunk (remote control
button with embossed trunk icon).
).
This function activates for few seconds the siren, if a door is open being the system armed.
This function activates the optical signaling, according to the connection. It should be activated in
some particular vehicles on which connection is made directly on the wire from the “hazard” button..
9.1 - ACOUSTIC SIGNALLING
9.2 - REMOTE CONTROLLED PANIC ALARM
9.3 - CURRENT ABSORPTION SENSOR
9.4 - SYSTEM SELF-REARMING AND DOOR LOCKING
9.5 - PASSIVE ARMING
9.6 - CENTRAL DOOR LOCKING SETTING TIME
9.7 - COMFORT CLOSURE CONTROL
9.8 - DOUBLE IMPULSE IN OPENING
9.9 - SUPPLEMENTARY SIREN OUTPUT OR BOOT OPENING
9.10 -
9.11 - OPEN DOOR SIGNALING DURING ARMING TIME
9.12 - OPTICAL SIGNAL ACTIVATION SELECTION
!
!
PROGRAMMABLE FUNCTIONS DESCRIPTION
efore activating of the absorption sensor, it is suggested to consult the specific rules being in
force in your country (noise pollution)
Together with the system self-rearming, the automatic door locking of the vehicle is done when
running.
Being closed all the doors of the vehicle, turn the ignition key to “ON”; after 20”, all doors will be locked.
By turning the ignition key to “OFF”, all doors of the vehicle will be automatically unlocked
Depending on connection, this function can activate the output for the siren (continuous tone) or for
the horn (intermittent tone
NEGATIVE OUTPUT SELECTION (DURINGALARM) FOR HORNS OR ADDITIONAL SIREN
.
If you open a door during this period, the procedure will be interrupted till the door is closed
10.0 - SYSTEM PROGRAMMING
The system has been previously programmed with standard configuration during manufacturing
procedure by Gemini.
:
With the system being disarmed, turn the vehicle ignition key to “ON” position.
The status LED stay on for one second; during this time, push together the two buttons of the
remote control with embossed the padlocks (button 1or 2).
Starting of programming procedure is indicated by two acoustic signals, one with high tone and one
with loud tones, furthermore the status LED turns ON.
To able and disable the functions, follow the below table, take into consideration that every time the
push button of transmitter is pressed, the system goes to the following function.
(button 1 or 2), .
!
!
!
!
For programming modification proceed as follows
Furthermore,
according to the button being pressed two different acoustic signals are emitted
Pay attention to not modify the functions which have been programmed during the
installation.
!
!
Once the last function has been programmed, the alarm will confirm that the programming has
been disabled with two acoustic signals with low tone, one acoustic signal with high tone,
.
Turn the vehicle ignition key to “OFF” position.
furthermore the LED will be turned off
When the optical pulse signaling feature is activated, the blinkers will ONLY emit optical
signals during an alarm cycle.
!
9.13 - DOORS PUSH-BUTTONS POLARITY SELECTION
This function modifies the alarm input signal (positive or negative) according to the signal from the
door’s button.
FUNCTION STATUS BUTTON “1” BUTTON “2”
Arming/disarming acoustic signalling
Panic alarm or car finder
Current absorption sensor
System self-rearming
System passive arming
Setting of opening/closing time (1” or 6”)
25” comfort closure
Lock double impulse in opening
Selection of supplementary siren or boot
opening by remote
Selection of continuous sound
(supplementary siren) or alternate
(vehicle’s claxon)
“Doors opened” signalling during system
arming
“Standard” or “impulse” optic signalling
activation
Selection of doors input polarity
By turning the ignition key to “OFF” in any moment of the programming procedure, the
latter will stop and successive functions will remain unchanged.
!
Enable
Enable panic
Enable
Enable
Enable
Enable 6”
Enable
Enable
Enable boot
opening
Elternate sound
(vehicle’s claxon)
Enable
Enable “impulse”
Enable positive
polarity
Disable
Enable car finder
Disable
Disable
Disable
Enable 1”
Disable
Disable
Enable
supplementary
siren
Continue sound
(siren)
Disable
Enable
“standard”
Enable negaive
polarity
Enabled
Enabled
Disabled
Disabled
Disabled
Selected 1”
Disabled
Disabled
Enabled
supplementary
siren
Enabled continue
sound
Disabled
Enabled
“standard”
Enabled negative
polarity
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 862 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 862 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 862

Gemini 862 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info