479882
4
Zoom out
Zoom in
Previous page
1/8
Next page
3.0 - NEW PIN-CODE PROGRAMMING
The procedure to program pin-code is specified here below as previously described, it is better to
personalize as customer has required.
In this example reported below, supposing that the pin-code is 5-4-6-7.
PAGE 06 - USER MANUAL
To carry out the operation successfully, make sure the required electrical connections
(door push-button and positive under key) are complete.
During PIN-CODE programming phase, if flashes are more than 9, this phase will be
invalid and the system will close the procedure.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
With the system being disarmed, open the driver side door and keep it open.
Turn the vehicle ignition ket to “ON” position.
The status LED will be turned on for one second; during this period, push simultaneously the two
buttons of the remote contol with embossed the padlocks.
A,
and the LED will lighted on.
Push simultaneously the two buttons of the remote contol with embossed the padlocks; the LED will
be turned off.
Turn the vehicle ignition ket to “OFF” position.
After a four second pause, state LED will start with the first sequence of 9 flashes.
At the fifth LED flashing (corresponding at nr.5, first digit of the PIN-CODE), push and release the
button on the status LED.
After a four second pause, state LED will start with a new sequence of 9 flashes.
Athe fourth LED flashing (corresponding at nr.4, second digit of the pin-code) push and release the
button on the status LED.
After a four second pause, state LED will start with a new sequence of 9 flashes.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
After a four second pause, state LED will start with the last sequence of 9 flashes.
At the seventh LED flashing (corresponding at nr.7, fourth digit of the pin-code) push and release
the button on the status LED.
The system will indicate the end of the procedure by two acousic signal with low tone and one with
high tone.
fter this procedure, two acoustic signals will be sent out one with acute tone and the other with
loud tone
4.0 - EMERGENCY DISARMING BY PIN-CODE
The procedure for emergency disarming by pin-code is following, reported below.
Kindly note that the standard pin-code programmed is of the four digit 1-1-1-1.
The same number used for pin-code programmation (5-4-6-7) has been used also for emergency
disarming example.
During PIN-CODE disarming phase, if flashes are more than 9, the procedure will be
.interpret as a theft attempt
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Cause an alarm condition.
Leave the system triggering for the standard alarm timing (about 30 seconds) and wait for the
“inhibit time between two alarm signalling” (LED switched off for 5”).
During this period push and release the push-button of the status LED.
the “emergency procedure disarming”.
After about 4 seconds the first 9 flashing sequence starts.
At the fifth LED flashing (corresponding at nr.5, first digit of the pin-code), push and release the
button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the fourth LED flashing (corresponding at nr.4, second digit of the pin-code), push and release
the button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the sixth LED flashing (corresponding at nr.6, third digit of the pin-code) push and release the
button on the status LED.
The LED will be switch off for about 4 seconds than a new 9 flash sequence will start.
At the seventh LED flashing (corresponding at nr.7, fourth and last digit of the pin-code) push and
release the button on the status LED.
If the code is right, the end of the emergency disarming by pin-code will be indicated by the alarm
with visual/acoustic signalling.
Vice versa, if the inserted numbers are wrong, the alarm will start triggering again; in this case,
repeat all procedure.
From now and on the system is in
This function is used ONLY if “system self-rearming” or “passive arming” functions
have been programmed.
This function is used when the alarm disarming is required, e.g. for maintenance, without any
intervention to the previous programming
o restore normal operating of programmed functions, arm the alarm via the control
T
.
For procedure activation follow the indications reported below:
Arm the system and wait for the end of arming neutral time.
Put the electronic key into the specific receptacle.
Three acoustic signals of the siren and three optical signals of turn signals will indicate the system's
disarming and the above mentioned function deactivation.
remote
!
!
!
!
.
USER MANUAL - PAGE 07
5.0 - GARAGE FUNCTION
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 861 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 861 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 861

Gemini 861 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info