479877
4
Zoom out
Zoom in
Previous page
1/7
Next page
8.0 - COMPLETE ELECTRIC DIAGRAM
PAGE 06 PAGE 07
6.0 - CONNECTOR TABLE
!
!
!
BLACK 2-way plug holder connector, RED and BLACK wires: connection of the signalling
LED.
BLACK 2-way female holder connector, GREEN and BROWN wires: connection of the
electronic key receptacle.
BLACK 4-way female holder connector, GREEN/BLACK, BROWN and PINK wires:
connection of volumetric sensors (hyperfrequency or ultrasonic module).
4 - Ground
5 - Positive
11 - Engine immobiliser
12 - Engine immobiliser
20 - Positive under key
7 - Bonnet switch negative input
(if not on CAN BUS line)
1 - Positive with system armed (+A)
9 - Additional siren negative control
6 - Comfort output or satellite system activation output (both
negative)
15 - Turn signals positive/negative common
14 - Turn signals positive/negative output
16 - Turn signals positive/negative output
2 - CAN BUS line (CAN-L)
3 - CAN BUS line (CAN-H)
BLACK marked M
BLACK marked R
BLACK marked H
BLACK marked H
YELLOW
GREEN
PINK
YELLOW/BLACK
WHITE/BLACK
WHITE/RED
ORANGE
ORANGE
LIGHT BLUE
LIGHT BLUE/GREY
WIRE POSITION AND FUNCTION
WIRE COLOUR
In the alarm wiring two two-way connectors and a four-way connectors are present,
whose functions are described below.
!
CONNECTION TO THE HAZARD
PUSH-BUTTON (if possible, see specification)
CONNECTION TO THE
TURN SIGNALS
ORANGE
WHITE/RED
Connect to the
hazard signal just
one orange wire
To be connected
to a positive or to a
negative, according
to the vehicle
hazard signal
ORANGE
WHITE/RED
ORANGE
To be connected
to the wires of
turn signals
To be connected
to a fixe
positive(+30)
7.0-C
Connection and programming must be made according to the turn signals connection mode (standard
or hazard), as indicated in the installation sheets.
The “standard configuration” module is set for connections as shown in the first design.
To modify configuration from “standard” to “impulse”, please follow instructions given in the
programming paragraph and then proceed with wiring connections as shown in the second design.
ONNECTION FOR TURN SIGNALS ACTIVATION
NOTE: the function of IMPULSE
OPTICAL SIGNALS must be enabled
NOTE: the function of IMPULSE
OPTICAL SIGNALS must be not enabled
5A
+
Battery
12 VOLTS
10A
8A
MAX !
ALARM SYSTEMS
7059
02 0176
e
12
Made in Italy - For all EU
12VDC - 2.4GHz
+
-
5123
BLACK marked M
GROUND
POSITIVE
BLACK marked R
Red
Black
Green
Brown
YELLOW-BLACK
WHITE-RED
Supplementary siren (
)
negative
output during alarm step
ORANGE
ORANGE
Turn signals relay common
Turn signals
YELLOW
+30
Positive under key
BLACK marked H
BLACK marked H
Engine block
Comfort output or satellite
system activation
(both negative)
GREEN
BLACK marked V
Cm.300
Bonnet push-button
Positive with
system armed (+A)
PINK
WHITE/BLACK
CAN BUS
signal
LIGHT BLUE (CAN-L)
LIGHT BLUE-GREY
(CAN-H)
Pink
Brown
Green/Black
Made in Italy
7833
W
ALARM SYSTEMS
ELECTRONIC KEY
20
10
19
9
8
17
18
7
6
5
4
14
3
13
2
12
1
11
20
18
19
8
9
7
17
Connecton
of 7833 unit
with equipped
siren
It is reccomended to
insert a 5A fuse.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7832 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info