479862
7
Zoom out
Zoom in
Previous page
1/9
Next page
PAG . 12
PAG . 13
LEARNING OF NEW CONTROL DEVICES
ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device memorizing procedure will be
invalidated.
ATTENTION: do not modify the bonnet position, otherwise instead of
saving to memory new devices, deletion of existing ones in the alarm´s
memory will take place.
The alarm can save to memory a maximum number of 12 control devices,
either radio controlled, or electronic keys, TAG cards or magnetic contact (the
later as a protection device).
Proceed as follows:
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
Turn the ignition key to “ON”.
Turn the ignition key to “OFF”.
Re-turn the ignition key to “ON” for three consecutive times (ignition key to
“ON” and “OFF”), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to “ON”.
The alarm will indicate the procedure starting of new control device or
magnetic contact learning, by two long turn signal flashes and two acoustic
signals, one acute tone and the other loud tone.
Now the alarm is waiting for receiving the device code.
Press the radio control push-button 1, introduce the electronic key in the
specific receptacle, press the TAG card button or make the magnetic
contact to transmit (bring near and then take away contact and magnet),
according to the device to be saved to memory.
In all four cases, the alarm will indicate the new device learning, by one turn
signal flashing and one acute tone signal.
Repeat the procedure to save to memory other devices.
Turn the ignition key to “OFF”.
The procedure completion will be indicated by one long turn signal flashing
and one loud tone signal.
!
!
!
!
!
!
!
!
!
DELETION OF PROGRAMMED CONTROL DEVICES
ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device deletion procedure will be
invalidated.
NOTE: keeping the bonnet close for less than four seconds, the device
deletion via radio will be unsuccessful.
NOTE: the control device deletion does not imply any modification of
The alarm is equipped with a deletion procedure of new control devices, either
radio controlled, or electronic keys, TAG cards or magnetic contact (the later as
a protection device).
Proceed as follows:
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
Turn the ignition key to “ON”.
Turn the ignition key to “OFF”.
Re-turn the ignition key to “ON” for three consecutive times (ignition key to
“ON” and “OFF”), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to “ON”.
The alarm will indicate the procedure starting of new control device or
magnetic or magnetic contact deletion, by two long turn signal flashes and
two acoustic signals, one acute tone and the other loud tone.
Close the bonnet.
The led will be illuminated constantly.
Keep the bonnet close till the moment, the complete deletion of devices
via radio, will take place (after about four seconds).
The procedure completion will be indicated by led´s turning off, by one
long turn signal flashing and one loud tone signal.
Turn the ignition key to “OFF”.
!
!
!
!
!
!
!
!
!
!
Nominal tension
Nominal supply voltage range
Current absorption @ 12Vdc
Turn signal contact rating
Engine block contact rating
Alarm triggering
Max positive current with system armed (+A)
Sirene output current capacity
12 Vdc
< 2mA with systme armed
and led
10A a 20°C
30 sec.
9 15Vdc¸
flashing
8A a 20°C
700 mA
3A
TECHNICAL DATA
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7590T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7590T in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info