Manual Gemini 7502 (page 6 of 13) (English)

479839

Zoom out

Zoom in

1/13

2) While the status LED is ON, press key 1 on the remote, the LED will turn off at once, reflecting

the activation of the GARAGE function.

To deactivate the GARAGE function, it is sufficient to connect the alarm system with the remote.

Using the electronic key, to turn on and off the alarm system, does not reset the GARAGE function.

Learning Remote Codes

The system can learn up to 8 control devices from among the remotes and electronic keys and

contacts by radio.

If the peripheral devices of the security system have been properly connected (DOOR pushbutton

and BONNET pushbutton), the codes can be learned without intervening directly on the alarm

control unit. This simplifies operations and reduces intervention time.

NOTE: To activate the user/installer learning procedure, the security system must be deactivated by

means of a remote or an electronic key, or by entering the emergency PIN-CODE. Moreover, the

PASSIVE ALARM ACTIVATION procedure must not have been activated.

If the system is in the PASSIVE ALARM ACTIVATION procedure, you must turn the system on and

off with a working remote or electronic key (or wait for the passive activation to end, and then

deactivate the system by entering the emergency PIN-CODE).

ACTIVATING THE LEARNING PROCEDURE:

1) Open, the driver’s side door and keep it open.

2) Open the bonnet and keep it open (obviously the protection pushbutton must be connected to

the alarm system).

3) Turn the ignition key to the ON position.

4) Press a previously learned remote key or put an already memorized electronic key into the

appropriate socket.

The system will signal entry into the learning function procedure by emitting a visual signal

consisting of two slow flashes of the turn indicators.

5) Press one of the two keys on the remote to be learned, or enter the new key to be memorized

into the appropriate slot. The system will confirm the memorization of the device by emitting a

visual signal consisting of one flash of the status LED.

6) Perform step 5) for all the devices to be memorised (remember: the maximum is 8).

DEACTIVATING THE LEARNING FUNCTION:

To end the learning function (after step 6), it is necessary to close the car DOOR and the BONNET

and turn the ignition key to the OFF position. The system will signal the exit from the learning

procedure by emitting a visual signal consisting of one flash of the turn indicators.

NOTE : THE 7503 ALARM SYSTEM DOES NOT ALLOW DELETION OF MEMORIZED DEVICES.

RELEASE PIN-CODE.

The alarm system being described here has a RELEASE PIN-CODE function which allows the user

to turn off the protection device (alarm and/or engine immobilizer) if supplied remotes do not work or

have been lost.

The PIN-CODE provided is made up of four digits from 1 to 9 set at the factory (1-1-1-1). The code

can be personalized by the user by using a “protected” programming procedure activated by means

of a working remote and the car ignition key.

RELEASING THE SYSTEM BY MEANS OF THE PIN-CODE

In order to release the system by means of the PIN-CODE, it is obviously necessary for the

protection device to be in the condition of full activation, i.e. alarm providing surveillance after the

initial neutral time or passive engine immobilizer activated.

In addition to knowing the exact digits of the PIN-CODE, the user must have the car ignition key.

DEACTIVATING THE ALARM:

In this situation it is necessary for the user to get into the car to cause an alarm condition. At the

end of the alarm cycle (lasting approx. 30”), the system will be in the neutral time between

successive alarms (duration approx. 5” – status LED emitting a continuous light). To activate the

release procedure during this phase it is necessary to turn the ignition key to the ON position and

then to the OFF position within approx. 3 seconds.

At the end of this operation, the status LED will turn off and the release procedure by means of the

PIN-CODE can be started.

ATTENTION: if the ignition key remains in the ON position for more than three seconds during the

neutral time between alarms, the system will interpret this situation as an attempted theft and

therefore a new visual/audio alarm cycle will start.

Once the release procedure has begun (i.e. when the ignition key returns to the OFF position), there

will be a pause of approx. 4 seconds, after which the status LED will emit an initial sequence of 9

flashes according to the following timing scheme: 0.5” ON – 1” OFF.

Each of these flashes can represent the number of the first digit of the release PIN-CODE. In other

words:

1st FLASH Ü NUMBER OF 1st DIGIT

2nd FLASH Ü NUMBER OF 2nd DIGIT

3rd FLASH Ü NUMBER OF 3rd DIGIT

4th FLASH Ü NUMBER OF 4th DIGIT

5th FLASH Ü NUMBER OF 5th DIGIT

6th FLASH Ü NUMBER OF 6th DIGIT

7th FLASH Ü NUMBER OF 7th DIGIT

8th FLASH Ü VALUE OF DIGIT 8

9th FLASH Ü VALUE OF DIGIT 9

To exemplify: let us suppose the PIN-CODE for the system is 4-3-2-1.

To enter the first digit (4), turn the ignition key to the ON position for at least one second during the

fourth flash of the status LED, or press the pushbutton on the LED (if LED art. 2324 is used) for at

least one second. This way the first digit (4) will be entered and after a pause of four seconds a new

sequence of nine flashes of the status LED will occur and it will be possible to enter the second digit

of the PIN-CODE (3). As in the procedure to enter the first digit, all you have to do to enter the

second digit is turn the ignition key to the ON position for at least one second during the third flash of

the status LED or press the pushbutton on the LED (if LED art. 2324 is used) for at least one

second.

And so on for the remaining two digits (2 and 1).

After entering the fourth digit, the alarm system will be released / deactivated and the set visual

signals will be emitted. Release by means of the PIN-CODE deactivates the ANTI-DISTRACTION

and PASSIVE ACTIVATION OF THE ENGINE IMMOBILIZER functions. These functions will be

reset upon the first system activation by remote.

In this case the system is not deactivated and the entire procedure must be repeated to attempt a

new release.

If during one of the four sequences of nine flashes no digit is confirmed (“0”), at the end of the ninth

flash the system will return to the normal surveillance cycle. In this case too, the entire procedure

must be repeated in order to attempt a new release.

PERSONALIZING THE PIN-CODE.

As mentioned above, the PIN-CODE is set at the factory with the following digits: 1-1-1-1. These

numbers are the same for all the alarms produced. Therefore the car user must personalize the

release code.

This operation can be performed as follows:

a) Deactivate the alarm system by means of a remote or an electronic key.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7502 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gemini 7502 Manual

Product: