479857
3
Zoom out
Zoom in
Previous page
1/10
Next page
By the push button no.2 of the remote controls it's possible to activate the PANIC alarm. In this condition it's possible to
test the internal siren circuit and the negative output for an external additional siren. It's possible to halt the PANIC alarm
by pressing the remote control push button no.2 again ( in this case there will be a neutral time of five seconds ).
DIAGNOSTIC SET-OFF.
To set-off the Diagnostic Mode and to enter in the Normal Mode it's possible to follow two different ways :
1. Insert an electronic key in the LED / Socket. To confirm the normal mode will be emitted three indicator lights flashes /
audible tones.
2. Press the button no.2 of the remote control to activate the PANIC alarm, then press the button no.1 of the remote
control in order to set- off the diagnostic mode.
IMPORTANT : At the end of the diagnostic mode the Dip-Switch no.5 must be set in OFF position !!
WIRING CONNECTIONS ( Disconnect the negative pole of the battery before the installation ).
FUNCTION WIRE COLOUR
Earth ( Negative pole of the battery )
BLACK marked “M”
Positive pole of the battery
BLACK marked “R”
Engine immobilisation
2 x BLACK marked “H”
Starting Key
BLACK marked “G”
Direction Indicator lights
2 x ORANGE
Door pin switch
GREEN-BROWN
Boot / Bonnet pin switches
BLACK marked “V”
Positive output - alarm armed
PINK
External sensors input
GREEN-BLACK
Electrical Boot release output - ( negative )
BLACK marked "HN"
External siren negative output
BLACK marked "GN"
Central Door Locking
YELLOW-BLUE, RED-BLUE, YELLOW-GREY,
RED-GREY, YELLOW-BROWN, RED-BROWN
VERY IMPORTANT!!
ALL WIRING IDENTIFICATION MUST BE REMOVED DURING THE INSTALLATION.
ALL POINTS OF CONNECTION SHOULD BE SOLDER ED AND INSULATED WITH HEAT SHRINKABLE TUBING, OR
USING ONLY THE ORIGINAL CONNECTORS AND PLUGS HOMOLOGATED BY THE MANUFACTURER .
FOR PREVENT ACCIDENTAL DISCONNECTION , ALL THE WIRES, THE ELECTRONIC KEY CONNECTORS AND
CODE BUS CONNECTOR MUST BE FITTED BY SOME PLASTIC CLAMPS ON THE ORIGINAL CAR HARNESS.
OPERATING INSTRUCTIONS ( installer ).
ALARM ARMING - BY REMOTE CONTROL.
Press the push button no.1 of the remote control. The arming of the alarm system is signalled by one direction lights pulse
/ audible tone .
The central door locking will be closed with the pulse programmed during the installation.
ALARM DISARMING - BY REMOTE CONTROL.
Press the push button no.1 of the remote control. The disarming of the alarm system is signalled by three direction lights
pulses / audible tones . If an alarm condition occurs during the arming period the direction lights pulses / audible tones
will be five instead of three ( see also " LED ALARM MEMORY" chapter ). The central door locking will be opened with
the pulse programmed during the installation.
ALARM ARMING / DISARMING - BY ELECTRONIC KEY.
It's possible to use the electronic keys to arm and disarm the alarm system. In this case the central door locking are not
powered and a entry delay time of 10 seconds is provided in order to disarm the system without false alarms.
In order to override the audible tone see the "AUDIBLE TONES SETTING" chapter.
SPECIAL FUNCTIONS.
PANIC ALARM.
If the dip-switch no.1 is set in ON position, it's possible to obtain a PANIC ALARM by pressing the push button no.2 of the
remote control.
The length of the panic alarm period is 29 seconds, but it's possible to halt this alarm by pressing again the push button
no.2 of the remote control. The panic alarm is available with the alarm system disarmed, or armed after the neutral time of
45 seconds.
ELECTRIC BOOT RELEASE.
If the dip-switch no.1 is set in OFF position, it's possible to use the push button no.2 of the remote control to open the
electrical lock of the boot on vehicles equipped with this feature. The electric boot release is available with the alarm
system disarmed or armed. If the alarm system is armed a delay time of 60 seconds is provided in order to open the boot
without false alarms, during this time period the LED is lighted in fix mode.
EXTERNAL SENSOR INPUT / ALARM ARMED POSITIVE OUTPUT OVERRIDE.
During the first 25 seconds of the neutral arming period it's possible to override the external sensor input and the positive
output ( +A / PINK wire ) in order to halt the window raise. This feature is obtained by pressing the push button no.2 of the
remote control and it's signalled by a direction lights pulse; on vehicles equipped with the "Comfort Closing System" - (
dip-switch no. 3 in ON position ) the external sensor override feature halts the central door locking pulse in order to stop
the window raise.
To exclude the external sensor input with the window totally closed it's necessary to wait the total closure and then press
the push-button no. 2 of the remote control.
AUDIBLE TONES SETTING.
This alarm system allows to the user to switch ON / switch OFF the audible tones by the remote control.
AUDIBLE TONE SWITCH OFF.
1. Turn the ignition key in ON position ( without start the vehicle engine !! ).
2. Press the push-button no.1 of the remote control for more than 3 seconds. To confirm the audible tones switch
OFF a LED flash will be emitted.
3. Turn the ignition key in OFF position.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7350 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info