479845
2
Zoom out
Zoom in
Previous page
1/7
Next page
DESCRIPTION:
GEMINI 6102
- Remote controlled, compact alarm with dynamic code.
- Blinker and electronic siren, central door locking control, electric windows and sunroof
closure (for selected vehicles equipped with pac-comfort” system).
- Perimetrical protection.
- LED’s memory.
- Engine immobilisation.
GEMINI 6103
- Remote controlled, self-powered, compact alarm unit with dynamic code.
- Blinker and electronic siren, central door locking control, electric windows and sunroof
closure (for selected vehicles equipped with pac-comfort” system).
- Perimetrical and volumetric protection (only for 6103 GEKT and 6103 IRKT).
- LED’s memory.
- Engine immobilisation.
- Internal circuit to control the battery backup, in case of totally discharge of the battery or
contacts breaking, the LED does not visualise any signals (only for 6103 IR).
Both systems are supplied with a 2 buttons transmitter (art. 5009) and a 1 button transmitter
(art. 6108) and 2 keys for ON-OFF.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
- Earth ê BROWN wire.
- Battery positive terminal ê RED wire.
- Engine immobilisation ê GREY wire.
- Ignition live ê YELLOW wire.
- Direction indicator lights ê ORANGE wires.
- Door pin switch ê GREEN-BROWN wire.
- Boot/bonnet pin switches ê GREEN wire.
- Positive alarm armed ê PINK wire.
- Entry sensors ê GREEN-BLACK wire.
- Outlet negative control ê YELLOW-BLACK wire.
additional siren
- Central door locking ê YELLOW-RED, BROWN-RED, YELLOW-GREY, RED-
GREY wires.
Note: the wiring harness has two BLACK connectors. Connect the 4 pin BLACK
connector to the ultrasound module and the 2 pin BLACK connector to the LED.
USEFUL SUGGESTIONS FOR THE INSTALLATION.
- Connect the power feed wire to the battery positive terminal and the earth directly to the
vehicle frame.
- On catalysed vehicles the engine immobilisation must be carried out on the fuel pump.
- Avoid routing connection wires next to interference sources (sparking plug cables, high
voltage coil )
- Install the alarm in the engine compartment protected from water spray.
- If you install an ultrasonic module, the ultrasonic heads must be positioned at the top of
each windscreen pillar and must be pointing at each opposite diagonal corner away from
the facia outlets.
WORKING DESCRIPTION :
- Alarm activation : push on the transmitter’s BLACK button. The activation is signalled by
one pulse of the direction indicator lights and one acoustic signal (can be isolated).
- Alarm activation-isolating ultrasonics and voltage drop: push on the transmitter’s RED
button.
The activation is signalled by 2 pulses of the direction indicator lights and two acoustic
signals (can be isolated).
To de-activate this function, while alarm de-activated, turn the vehicle ignition key to ON
position for 15 seconds.
- Alarm de-activation: push on the transmitter’s BLACK button.
The de-activation is signalled by 3 pulses of the direction indicator lights and 3 acoustic
signals (can be isolated). 5 pulses of the direction indicator lights if an alarm condition has
occurred.
SPECIAL FUNCTIONS:
Panic:
s obtained by pushing on the transmitter’s RED button (art. 5009) while the alarm is
activated. The siren will activate for 10 sec.. To de-activate the siren within 10 sec. push
again on the transmitter’s RED button.
Passive arming:
Position the dip-switch Nr. 3 in ON position. The passive arming will activate 30 sec. after
the engine is switched off if one door is opened. This function allows to activate the alarm
and the engine immobilisation without controlling the central door locking.
Self-learning of the code of a new transmitter:
While alarm de-activated, position the dip-switch Nr. 4 to ON ; turn the ignition key to ON
position and push on the transmitter’s button. The LED will signal the learning by a pulse.
Turn again the ignition key to OFF position and the dip-switch Nr. 4 to OFF position, verifying
with the transmitter the activation/de-activation of the alarm. It is possible to codify a
maximum number of 4 transmitters.
Ultrasound exclusion by a one-channel transmitter (art. 6108):
While alarm de-activated, turn the ignition key to ON position, push on the transmitter’s
button. The LED will signal the memorisation of the ultrasound exclusion with a 2 sec. pulse.
LED’s memory:
While alarm de-activated it is possible to verify if an alarm condition has occurred.
Signalling LED Alarm triggering
¬¬l¬¬
Ignition live.
¬¬¬l¬¬¬
Voltage drop sensor.
¬¬¬¬l¬¬¬¬
Wires cut, door and boot/bonnet pin switches.
¬¬¬¬¬¬l¬¬¬¬¬¬
Lack of feed , alarm by OFF-ON.
l LED OFF (2 seconds) ¬ LED ON (1 second)
The exit delay period is 15 sec. for each alarm.
Attention : do not turn the unit on with the key switch before the installation is complete. You must then wait
for a maximum of 60 minutes before completing the self-powered test. All other alarm functions will perform
as standard.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 6102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 6102 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 6102

Gemini 6102 User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info