479842
2
Zoom out
Zoom in
Previous page
1/7
Next page
DESCRIPTION:
GEMINI 4203RC
- Remote controlled compact, self powered alarm unit with dynamic code (Frequency
433.92 MHz)
- Blinker and electronic siren, central door locking control, electric windows and sunroof
closure for selected vehicles equipped with “Comfort Closing Systems”.
- Perimetrical protection (only for 4203RC-KT) and incorporated chock sensor.
- Engine immobilisation.
GEMINI 4202RC.
- As 4203RC not self-powered.
Both systems are supplied with 2 codified transmitters (art. 6208GE) and 2 keys for ON/OFF.
WIRING CONNECTION (for the installer).
Disconnect the negative terminal of the battery and only re-connect after the installation is
complete.
- Earth ê BLACK initialled M wire.
- Battery positive terminal ê BLACK initialled R wire.
- Engine immobilisation ê BLACK initialled H wires.
- Ignition live ê YELLOW wire.
- Direction indicator lights ê ORANGE wires.
- Door pin switches ê GREEN-BROWN wire.
- Boot/bonnet pin switches ê GREEN wire.
- Positive alarm armed ê PINK wire.
- Sensors inlet ê GREEN-BLACK wire.
- Central door locking ê YELLOW-RED, RED-BROWN, YELLOW-
GREY, RED-GREY wires.
Note: The wiring harness has two BLACK connectors. Connect the 4 pin BLACK connector
to the module (art 5023 or 5123) and the 2 pin BLACK connector to the LED (art. 2323/S).
USEFUL ADVICE FOR INSTALLATION:
- Connect the power feed wire to the battery positive terminal and the earth directly to the
vehicle frame.
- On catalysed vehicles the engine immobilisation must be carried out on the fuel pump.
- Avoid routing connection wires next to interference sources (sparking plugs cables, high
voltage coil).
- The alarm must be installed in the engine compartment protected from moisture.
- If you install an ultrasonic module, the ultrasonic heads must be positioned at the top of
each windscreen pillar and must be pointing at each opposite diagonal corner away from
the facia outlets.
ULTRASONIC ADJUSTMENT AND TEST PROCEDURE:
- Adjust the sensor to a medium sensitivity.
- Arm the alarm with the transmitter.
- Wait 40 seconds and generate some small vibrations on the vehicle. Increase the
sensitivity and repeat test until the alarm triggers.
OPERATING INSTRUCTIONS:
- Alarm activation: press the transmitter’s button (number 1).
The activation is signalled by one pulse of the direction indicator lights and one acoustic
signal (can be isolated).
- Alarm activation - isolating ultrasonics and voltage drop: press twice on the
transmitter’s button (number 2).
The activation is signalled by two pulses of the direction indicators lights and two
acoustic signals (ca be isolated).
- Alarm de-activation: press the transmitter’s button (number 1).
The de-activation is signalled by 3 pulses of the direction indicator lights and three
acoustic signals (can be isolated). 5 pulses if an alarm condition has occurred.
ACTIVE FUNCTIONS 5 SEC. AFTER THE ALARM ARMS:
- Cut of the power feed.
- Engine immobilisation.
ACTIVE FUNCTIONS 40 SEC. AFTER THE ALARM ARMS:
- Chock;
- Voltage drop;
- Door, boot and bonnet opening;
- Sensors inlet.
SPECIAL FUNCTIONS
Panic: is obtained by pushing on the transmitter’s button number 2, while the alarm is
armed. The siren will activate for 15 seconds. To de-activate the siren within the 15
seconds, press on the transmitter’s button (number 2).
Siren exclusion:
This function is obtained by turning the ignition key to ON position while the alarm is de-
activated. Press on the transmitter’s button (number 1). The siren exclusion is signalled by
one flashing of the LED. Turn the ignition key to OFF and activate the alarm by pushing on
the transmitter’s button number 1.
The activation of the siren is obtained by de-activating and activating the alarm.
Passive arming:
Set the dip switch Nr. 3 to ON position. The passive arming will activate 15 sec. after the
engine is switched off if one door is opened. This function actives the alarm and the engine
immobilisation without controlling the central door locking.
Self-learning of the code of a new transmitter.
1- De-activate the alarm with a transmitter.
2- Connect the WHITE wire found near the BLACK loop to a body earth.
3- Turn the ignition key to ON position for 1 second (the direction indicator lights will
switch ON) and then to OFF.
4- With the key to OFF position, push the button of one transmitters to codify. The code
memorisation is signalled by a 0,5 sec. pulse of the direction indicator lights.
Note : Push the transmitter’s button within 30 seconds after the ignition key is turned to
OFF position.
It is possible to learn a maximum number of 8 transmitters following the operation from
point 3. At the end of the memorisation disconnect the WHITE wire ad isolate it.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 4202RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 4202RC in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info