749310

Geha X5 Shredder Manual

8
Zoom out
Zoom in
Previous page
1/48
Next page
8
STARTING SHREDDER
The X5 is operated by means of a sliding switch located at the top of the shredder.
This switch can be set to three positions: AUTO, OFF, REV.
Set the sliding switch to AUTO to activate automatic paper intake as soon as a document
is placed in the feeder slot, triggering the release switch in the feeder opening.
If the sliding switch is set to OFF, the shredder does not automatically start up when a
document is placed in the feeder opening. We recommend setting the switch to this position
when the shredder is not in use.Set the sliding switch to REV, if you wish to operate the
shredder continuously in reverse mode. This is required to clear a paper jam in the feeder.
PREVENTING PAPER JAMS AND OVERLOADING
The X5 can shred up to 5 sheets (DIN A4, 70g/m²) at a time and can handle documents
of up to 220mm in width.
If you wish to shred smaller pieces of paper such as envelopes and sales receipts, insert
them at the centre of the feeder slot to ensure that the switching sensor is triggered.
The X5 is equipped with a motor overload circuit breaker. A normal operating cycle
for shredding at maximum load takes 2 minutes, which must be followed by a break in
operation. The power supply to the shredder motor is automatically interrupted in
the following cases:
1. Continuous operation of the document shredder at maximum capacity over
a prolonged period of time, i.e. for more than 2 minutes without interruption.
2. Simultaneous insertion of more than 5 sheets of paper (DIN A4, 70g/m²)
or feeding of paper in a direction other than longitudinal.
Under the above conditions, the automatic overload circuit breaker of the motor might be
triggered, interrupting the power supply to the device. If this occurs, proceed as follows:
1. Disconnect the power plug from the mains socket and wait for a minimum of
60 minutes until the overload circuit breaker is automatically reset. Remove the paper
by pulling it upwards out of the cutting unit and tear off any excess paper.
2. Reconnect the power plug to the mains socket and set the sliding switch to REV.
Remove the remaining paper from the shredder blades. Set the sliding switch to AUTO.
If necessary, repeat this procedure.
3. When the feeder slot is again unblocked, continue shredding by setting
the sliding switch to AUTO.
In the event of a minor short paper jam, the power supply is interrupted only temporarily.
This means that the device can be restarted as soon as the jam is removed.
Manual__X5Basic:Layout 1 07.09.10 16:36 Seite 8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geha X5 Shredder at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geha X5 Shredder in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info