544888

Geba Tronic ROLLOTIMER Comfort Manual

3
Zoom out
Zoom in
Previous page
1/3
Next page
Programming of ROLLOTIMER Comfort - with S/D sensor
1. Enter programming mode
Press ▲ (UP) and ▼ (DOWN) simultaneously for
approx. 3 seconds.
2. Sun function
setting
(only with S/D
Sensor)
Setting of value
☼ 0 ... E
Use ▲ (UP) to set the value or E for calibration
of the current lightning conditions.
Press ▼ (DOWN).
3. Dusk function
setting
(only with S/D
Sensor)
Setting of value
0 ... E
Use ▲ (UP) to set the value or E for calibration
of the current lightning conditions.
Press ▼ (DOWN).
Continue with point 2 programming of the Timer Comfor t- without S/D-Sensor
Value S/D Sensor
Value Sun sensor Dusk sensor
0 Deactivated / off Deactivated / off
1 Low brightness Low dusk
2 Medium brightness Medium dusk
3 High brightness High dusk
E Calibration of the sensor
Calibration of the sensor
Settings : Sun / Dusk sensor, (Art. No.: 607.S000.01)
This is only available if a S/D sensor is connected and if the automatic mode is activated. For the
installation of the sensor please see the next page of the manual. The Timer will require approx. 10
seconds for the correct identification, after switching on.
Sun function
If a S/D sensor is connected, activated and the automatic mode is activated, a sun symbol will appear
in the display. Exceeding the set brightness value is indicated by a blinking of this symbol. If the set
brightness value is exceed by more than 10 minutes, the blind will be lowered until the sensor is in the
shadow again. The Brightness is checked every 30 minutes. If the set value is underrun for 10
minutes the blind goes up again.
Dusk function
If a S/D sensor is connected, activated and the automatic mode is activated, a moon symbol will
appear in the display. Exceeding the set dusk value is indicated by a blinking of the symbol. The
function of the dusk value is switched on by the automatic set ▼ (DOWN) operation mode. If the value
is exceeded by 10 mor e than minutes, the blinds will close completely. Please note that any light
source near the sensor can interfere with its function.
Calibration of the S/D sensor
If you experience any problems with the preset brightness values, you can calibrate the S/D sensor
individually to the desired brightness. When you have the desired brightness, select the value „E“.
Then press ▼ (DOWN) to the current brightness as value 2 – medium brightness/dusk. Define and
save.
Attachment of the Sun / Dusk sensors
Remove the upper part together with the two frames of the ROLLOTIMER.
Now have a look on the image below. Connect the sun / dusk sensor with the plug.
Please make sure, that the C-frame (extremely remote frame) has a cable through hole on the
requested side.
Plug to connect the
sun / dusk sensor
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geba Tronic ROLLOTIMER Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geba Tronic ROLLOTIMER Comfort in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Geba Tronic ROLLOTIMER Comfort

Geba Tronic ROLLOTIMER Comfort User Manual - German - 4 pages

Geba Tronic ROLLOTIMER Comfort User Manual - Dutch - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info