13553

GE AJHS08DCB Manual

9
Zoom out
Zoom in
Previous page
1/76
Next page
Horizontal louvers
on the front grille
let you control the
air direction up
and down.
Remove the front
grille to adjust the
vertical louvers
side-to-side to
direct the air left
or right.
9
Temperature Limiting
Limiting the maximum and minimum settings
prevents users from turning the control to the
extreme heat or cool positions.
The normal range of the temp control is
approximately 60°F to 85°F. The control range
may be narrowed by the use of the temperature
limiting screws located behind the control panel.
Each position equals approximately 3°F.
Air Direction
Fan Switch
To reach the fan switch(es) remove the
front grille.
On Heat/Cool and Heat Pump models, the fan switch
levers are located in holes accessed through the
control box. The top switch is for COOL settings
and the bottom switch is for HEAT settings.
Use a small screwdriver to change the setting.
The unit is shipped from the factory set in the
CONT setting for COOL and in the CYCLE setting
for HEAT.
Cool only models have a rocker switch on the
front of the control box.
When set at CYCLE (down) the fan cycles on and
off when cooling. When set at CONT (continuous,
up) the fan runs all the time, providing a more
balanced temperature. The unit is shipped in
the CONT setting.
www.GEAppliances.com
Limits
heat
temp
Limits
cool
temp
Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support
Vent Control
The vent control is located behind the front
grille on the right side of the air discharge area.
When set at CLOSE, only the air inside the room
will be circulated and conditioned. When set at
OPEN, some inside air is exhausted outside.
To open or close the vent:
1. Remove the front grille.
2. Remove the vent card screw.
3. Remove vent card, turn it over and replace
it by locating rear hole in card over locating
pin inside air discharge and reattaching
screw at front.
Locating hole
Screw hole
OPEN position
(Mesh end toward back)
CLOSE position
(Mesh end toward front)
Locating hole
Screw hole
The unit leaves the factory set at the CLOSE position.
(Depending on model)
or
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GE AJHS08DCB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GE AJHS08DCB in the language / languages: English as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info