813467
11
Zoom out
Zoom in
Previous page
1/80
Next page
11
GB
INSTALLATION
GENERAL
TOOLS REQUIRED
1 X Screwdriver
UNPACKING THE APPLIANCE
WARNING! DO NOT use this appliance if any part has been
exposed to water.
Immediately call a qualified service technician to inspect and to
replace any part of the electrical system if necessary.
Open the packaging carefully and remove the polystyrene.
Remove and discard the plastic bag.
Keep plastic wrapping away from children.
Be responsible when handling the packing materials.
Check all parts and accessories are removed before disposing of
any packaging.
If necessary keep the original packaging for future transport and/
or storage.
Test the appliance before installation.
This appliance is heavy and does not require
anchoring to the hearth or floor, but in certain
circumstances the appliance can become
unstable e.g. when leaning on the appliance. If
this is likely, secure the appliance to the hearth
or floor with suitably strong fixings.
LOCATING THE APPLIANCE
The appliance may be installed virtually anywhere in your home.
However, when choosing a location ensure that the general
instructions are followed.
For best results, install out of direct sunlight.
If the power cord is damaged contact your Gazco retailer for a
replacement. Only use genuine Gazco parts on this appliance.
The appliance should be located close to a suitable mains socket
to enable connection.
The electrical socket must be easily accessible to allow
disconnection when the appliance is fitted.
This appliance must stand on a clean, level, firm surface.
Do not stand the appliance on a carpet. Ensure that furniture,
curtains etc. are positioned no closer than 1m and the appliance
stands on a surface that can withstand temperatures of 90°C for
prolonged periods. Do not allow rugs to be placed within 500mm of
the front of the appliance.
Ensure that curtains and furniture are not positioned close to the
chosen position, as this would create a potential fire hazard or
block the heater outlet ducts.
WARNING! KEEP ANY COMBUSTIBLE MATERIALS AT LEAST
1M FROM THE FRONT AND SIDES OF THE APPLIANCE.
ALL INGLENOOK FIREPLACE OPENINGS:
For all models the dimensions required for an inglenook installation
can be calculated by adding 225mm (9”) to the height of the
appliance and 150mm (6”) to each side. An additional 50mm (2”)
must be added to the depth to provide adequate space behind the
appliance.
SERVICING AND SUPPORT
Servicing and Support
To keep your appliance looking and performing at its best, it must
be serviced annually. This service must be undertaken by a suitably
qualified individual and your retailer can organise this for you.
Alternatively, Gazco offer a manufacturers premium service with our
friendly team of qualified engineers which can be booked at www.
gazco.com/support
SERVICING REQUIREMENTS
DURING SERVICING OF THIS APPLIANCE IT MAY BE
NECESSARY TO CUT CABLE TIES IN ORDER TO
ACCESS AND REMOVE SOME OF THE PARTS.
THESE MUST BE REPLACED WHEN
REASSEMBLING THE APPLIANCE.
THIS APPLIANCE MUST ONLY BE SERVICED BY A SUITABLY
QUALIFIED PERSON.
BEFORE UNDERTAKING ANY WORK ON THE APPLIANCE:
SWITCH OFF THE APPLIANCE AND ISOLATE THE POWER
SUPPLY ENSURING THERE IS NO POWER TO THE APPLIANCE.
Wait for at least 10 minutes until the appliance has cooled down.
Remote Handset Battery Replacement
Replace with 2 AAA batteries. Make sure the batteries are installed
correctly in the remote control.
NOTE: The remote control has a Battery Status
indicator (top right corner), after an extended
period of displaying empty the LED screen will
cease to function despite the handset still being
able to send commands.
Replace the batteries to restore display.
Maintenance of Motors
The motor used on the flame effect is pre-lubricated for extended
bearing life and requires no further lubrication. However, periodic
cleaning/vacuuming of the heater unit is recommended.
Resetting the Thermal Cutout Switch
The appliance is fitted with an Electronic Safety Control (E.S.). This
is a safety device which switches off the fire if, the appliance
overheats for any reason e.g. when covered.
If the heater stops operating whilst the flame effect continues
normally, this indicates that the E.S. Control is in operation.
The E.S. Control can only be re-set after the appliance has cooled
down.
To re-set the E.S:
Switch off the appliance (Manual On/Off switch) and leave for
approximately 120 minutes.
Remove any obstruction to the fan heater outlet or other internal
parts.
Switch on appliance and the E.S. Control will re-set. Ensure that
the appliance is functioning correctly. If the E.S. Control operates
again, the appliance should be checked by a competent
Electrician.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Stockton - Electric Range at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Stockton - Electric Range in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 6.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info