813415

Gazco Riva Vision Large MK1 Series Conventional Flue Manual

32
Zoom out
Zoom in
Previous page
1/36
Next page
32
the appliance, or if the handset is replaced, it will be
necessary to pair the handset with the appliance. Please
refer to Commissioning Section 2.
13.5 Ensure batteries are fitted and working in the handset.
13.6 Re-fit the touch pad control cable and the battery power
supply cable to the control box.
14. Main Injector
To change the main injector:
14.1 Undo the injector feed pipe.
14.2 Undo the lock nut from the injector and remove the
silencer.
14.3 Replace with the correct size injector.
14.4 Check for leaks.
15. Primary Aeration Plate
NOTALLMODELSHAVEAERATIONPLATES.REFER
TO TECHNICAL SPECIFICATIONS ON PAGE 13.
15.1 Remove the burner module as described in Replacing Parts,
Section 7.
15.2 Remove the fixing screw and slide the plate off the venturi.
15.3 Replace with the correct size plate and secure with the
screw. Ensure the lower edge of the plate is located over
the venturi flange, see Diagram 19.
19
Servicing Instructions - Replacing Parts
16. Debris Area Access
16.1 Remove the Steel frame (if fitted).
16.2 Remove the glass door assembly.
16.3 Remove the enamelled panels.
16.4 Remove the burner and splitter plate.
16.5 Isolate the gas supply.
16.6 Disconnect the isolating device from the inlet pipe on the
appliance.
16.7 Remove the 7 screws from the front of the loose box, see
Diagram 20.
20
16.8 Remove the 3 screws from the rear panel.
16.9 Lift the panel to disengage the locating brackets,
see Diagram 20.
16.10 Remove the 3 wing nuts and screws retaining the loose box,
see Diagram 20.
To release the box from the main body:
16.11 Rotate the front of the box upwards and draw the box
forward off the rear studs.
16.12 Ensure the gas pipe passes through the silicon seal in the
base of the box.
Any debris can now be removed through the aperture.
16.13 Replace in reverse order taking care not to damage the gas
pipe when replacing the box.
17. Changing Between Gas Types
In order to change between gas types, it will be necessary
to change the both the burner assembly and the complete
control assembly.
Contact your Gazco dealer for further information.
A kit of parts is available for this, always quote the Model
number and Serial number when ordering any spare parts.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva Vision Large MK1 Series Conventional Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva Vision Large MK1 Series Conventional Flue in the language / languages: English as an attachment in your email.

The manual is 3.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info