Manual Gazco riva Vision Large 50000 series Conventional Flue Instructions (page 21 of 32) (English)

813421

Zoom out

Zoom in

1/32

1. Servicing Requirements

IMPORTANT – The glass panel on this appliance should be

checked for any signs of damage on the front face of the

glass panel (scratches, scores, cracks or other surface

defects). If damage is observed, the glass panel must be

replaced and the appliance must not be used until a

replacement is installed. Under no circumstances should the

appliance be used if any damage is observed. Please isolate

the appliance until a replacement glass panel has been

obtained and installed. Replacement glass panels can be

purchased from Gazco via the retailer from which the

appliance was purchased or any other Gazco distributor.

This appliance must be serviced at least once a year by a

competent person.

All tests must be carried out in accordance with the current Gas

Safe recommendations.

1.1 Before Testing:

—Conduct a gas soundness test for the property ensuring

there are no leaks before servicing.

—Check the operation of the appliance before testing.

1.2 Special checks:

—Clean the burner using a vacuum cleaner with a soft

brush attachment. Ensure all debris is removed from the

burner ports.

—Clean away lint or fluff from the pilot.

—Clean away lint or fluff from under the burner.

—Check the spark gap on the pilot is correct.

1.3 Correct any faults found during the initial test.

1.4 Re-commission the appliance in accordance with

Commissioning Procedures of these instructions.

1.5 Advise the customer of any remedial work undertaken.

REPLACE BATTERIES BEFORE ATTEMPTING TO RECTIFY

ANY FAULTS.

Symptom Cause Remedy

3 Short beeps from

control

Batteries low in

appliance

Replace appliance

batteries

No ignition, 5 second

continuous tone (there

may be several short

beeps before)

Loose/damaged wire Check interrupter

block and wires

No ignition, no tone,

motor turns slightly

when operated

Receiver board

damaged

Replace receiver

No pilot flame and

control continues to

spark

Thermocouple circuit

wired incorrectly

Correct wiring

Pilot lights, control con-

tinues to spark, value

shuts down after 10 - 30

seconds

1. No spark at pilot

burner

2. Loose/damaged

wire

1. Rectify spark at

pilot burner

2. Check inter-

rupter and wires

ELECTRONIC CONTROL VALVE FAULT ANALYSIS

IGNITION FUNCTIONAL CHECK 1

PILOT WILL NOT LIGHT

Ensure there is no debris around the pilot assembly,

(e.g. soot, etc.) which could short the spark, clean the

area.

Operate the valve

control system in the

manual mode via the

touch pad or remote. Is

there a spark?

Consult User

Instructions and retry.

Check alignment of pilot

burner head. Change the

ignition lead.

See Replacing Parts,

Section 10.

Check isolation tap and

gas meter, retry.

Correct and

retry.

Purge the gas pipes and

retry.

GO TO THE NEXT

CHART IGNITION

FUNCTIONAL CHECK 2

SYSTEM OK

There is a blockage in the system, check the inlet test point,

the mag seating and valve. Check thermocouple leads for correct

orientation, condition and connection

Is the gas turned on to the

appliance?

Is the gas pressure correct?

Has the system got

any air in it?

Does the pilot light?

Is the control being

operated correctly?

Will the pilot light

with a match?

No Yes

Yes

Servicing/Fault Finding Charts

Servicing Instructions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gazco riva Vision Large 50000 series Conventional Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 2.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gazco riva Vision Large 50000 series Conventional Flue Instructions Manual

Product: