813402
15
Zoom out
Zoom in
Previous page
1/34
Next page
2.4 Gently remove the appliance from the crate and place into
its intended position. Locate the two securing holes in the
base subframe (those previously used to secure the
appliance to the crate), mark the positions on the floor and
place the appliance to one side (see Diagram 4).
4
AR1292
2.5 Drill the two holes and insert the wall plugs supplied. If the
gas supply is to enter through the floor under the appliance,
now is the time to make the necessary provision for the gas
supply.
2.6 Place the appliance back into position, level the appliance if
required by adjusting the 3 levelling screws and then secure
in place using the screws supplied (see Diagram 5).
5
AR1292
2.7 It will now be necessary to decide upon the flue route and
make the necessary flue connections. Two types of flue
termination are available, a horizontal terminal discharging
on a vertical wall or a vertical terminal discharging above
the roof level. Refer to Section 2 in Site Requirements for
allowable flue configurations in each instance.
15
INSTALLATION INSTRUCTIONS
INSTALLATION
2.8 When the flue configuration and lengths are known, it may
be necessary to fit a flue restrictor. Refer to Technical
Specification on page 10 for the correct restrictor size. This
should be fitted by removing the internal and external
spigots. The restrictor should be located between the
underside of the inner spigot and the air duct. Refer to
Diagram 6.
6
AR0627
2.9 Before any flue pipe is attached to the appliance, unwrap
the decorative cast iron collar and locate over the outer flue
spigot ensuring that the location lug locates in the notch at
the rear of the hole (see Diagram 7).
7
AR1293
2.10 When installing the horizontal terminal, decide on the
terminal position and measure the height from the top of
the appliance to the centre of the required hole. Refer to
Section 2 in Site Requirements for minimum and maximum
flue dimensions.
2.11 A 152mm (6") diameter hole is required to install the flue.
This can be achieved by either:
a) Core drill
b) Hammer and chisel
It is advisable to drill small holes around the circumference
when using method b. Make good both ends of the hole.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva Nemos Coprecci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva Nemos Coprecci in the language / languages: English as an attachment in your email.

The manual is 3.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info