813405
23
Zoom out
Zoom in
Previous page
1/40
Next page
23
2.4 Press the On/Off button () for at least 10 seconds. The
LED will flash on and off as normal during this time. When
the LED on the control lights up for at least 1 second
release the button.
2.5 Within 5 seconds of the LED going out press the () button
followed directly by the () button.
2.6 Within 20 seconds press the yellow button on the control
box (see Diagram 2). This may be easier using a pencil, ball
point pen or similar.
2
AR2510
Remote Handset
Pairing Button
2.7 The control box will beep to confirm the pairing operation
has been successful.
If there are any difficulties achieving pairing ensure that
the handset is set to Channel A. To do this follow the
steps below:
2.8 Press the On/Off button () for at least 10 seconds. The
LED will flash on and off as normal during this time. When
the LED on the control lights up for at least 1 second
release the button.
2.9 Within 5 seconds of the LED going out press the OK button
and then press the () button.
2.10 Disconnect the batteries from the control box and
reconnect after 10 seconds. The handset will now be set to
Channel A.
2.11 Attempt the pairing again following the steps below:
NOTE: These steps differ from the previous.
2.12 Press the On/Off button () for at least 10 seconds. The
LED will flash on and off as normal during this time. When
the LED on the control lights up for at least 1 second
release the button.
2.13 Within 5 seconds of the LED going out press the () button
followed directly by the () button.
2.14 Disconnect the battery pack from the control box and
reconnect after 10 seconds.
2.15 The motor on the valve will turn. Once it has stopped
repeatedly press and release the yellow button on the
control box until the control box beeps to confirm the
pairing operation has been successful.
3. CHANGING COMMUNICATION
CHANNEL
3.1 Press the On/Off button () for at least 10 seconds. The
LED will flash on and off as normal during this time. When
the LED on the control lights up for at least 1 second
release the button.
3.2 Within 5 seconds of the LED going out press the OK button.
3.3 Use the UP () and DOWN () buttons to select a new
communication channel. Assuming the appliance is set to
Channel A press the UP () button once to select Channel
B, and again to select Channel C. From Channel C press the
DOWN () button once to select Channel B, and again to
select Channel A.
3.4 Once the chosen channel has been selected disconnect the
battery pack from the control box and reconnect after 10
seconds. This completes the channel change.
3.5 To reset the communication channel to Channel A press the
On/Off button () for at least 10 seconds. The LED will
flash on and off as normal during this time. When the LED
on the control lights up for at least 1 second release the
button.
3.6 Within 5 seconds of the LED going out press the OK button.
Do not give any further commands for at least 10
seconds.
3.7 To return to normal operating mode wait for at least 5
seconds or press the On/Off button () once.
INSTALLATION INSTRUCTIONS
COMMISSIONING
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva F67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva F67 in the language / languages: English as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info