813406
32
Zoom out
Zoom in
Previous page
1/44
Next page
32
Servicing Instructions - Replacing Parts
3a. Pilot Burner Bracket
3.2 To remove the Pilot Burner Bracket:
- Disconnect the Ignition lead, see Diagram 6.
- Loosen thermocouple nut, see Diagram 7.
- Undo the brass nuts connecting the pilot pipe to the
brass fitting and the pilot unit and remove the pilot pipe,
see Diagram 7.
IMPORTANT Ensure not to lose the loose injector component.
- Remove the two nuts from the back of the bracket,
see Diagram 8.
8
Injector
Compression nut
Nut
Thermocouple Nut
Bracket Nut
Bracket Nut
3.3 The pilot unit can now be removed and the pilot components
can now be individually removed and replace.
3.4 Replace in reverse order.
3b. Electrode
3.5 Pull the ignition lead off the electrode and undo the retaining
nut, see Diagram 9.
9
3.6 Replace with a new electrode. Do not over-tighten the nut;
this could break the component.
3.7 Replace the ignition lead.
2.12 Hold the burner tray at the front, pull forward and rotate
upwards. Carefully remove the fuel bed and place safely to
one side. The unit can now be serviced.
IMPORTANT Ensure that the rubber seal is intact.
2.13 When replacing the unit ensure the location tabs engage
above the divider plate at the rear of the burner tray, see
Diagram 6.
6
2.14 To replace the burner, locate the inlet pipe onto the brass
fitting and loosely fit the nut. DO NOT TIGHTEN THE NUT
AT THIS STAGE.
2.15 Replace the 4 burner fixing screws. (Loosely replace the two
screws behind the burner fuel bed at the rear of the firebox
then replace the two screws at the front of the burner tray
and tighten then tighten the back two screws) see Diagram
4. Tighten the inlet pipe nut.
DO NOT OVER TIGHTEN THE SCREWS.
2.16 Light the appliance and check for leaks.
3. Pilot Unit
The pilot assembly consists of four components, which can
be individually changed, these are:
3a) Pilot burner bracket.
3b) Electrode
3c) Pilot Injector
3d) Thermocouple.
see Diagram 7.
7
Electrode
Thermocouple
Pilot Injector
Pilot Burner
Bracket
Ignition Lead Pilot Pipe
3.1 Turn off the gas supply at the isolating device, remove the
outer frame, glass door and the logs. Remove main burner,
see Section 2.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva 2 F670 Balanced Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva 2 F670 Balanced Flue in the language / languages: English as an attachment in your email.

The manual is 4.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info