813395

Gazco F40 Avanti Balanced Log Manual

25
Zoom out
Zoom in
Previous page
1/32
Next page
25
PILOT WILL NOT STAY LIT OR STOVE GOES OUT IN USE
Ensure there is no debris around the pilot assembly,
e.g. coal, soot etc. which could short the spark, clean the area.
Problem is with the
pipe work or
fittings which lead
to the stove. Correct
and retry.
Is thermocouple
connection good
in back of valve?
Replace
thermocouple.
Will pilot
stay alight?
Change magnetic safety unit.
Is the pilot flame of the
correct length? See
diagram 1 on page 20**
Change the
pilot unit.
Will pilot
stay lit?
With the pilot
running is the gas
pressure stated on the
data badge?
With the stove
running on full is the
gas at
the pressure stated
on the data badge?
Run for no more than
60 seconds
turn off, time interval
until mag unit shuts
with a click. Is this
greater than 7
seconds?
Run for a maximum of 60
seconds, turn off, time
interval until magnetic
safety unit shuts with a
click. Is this greater than 7
seconds?
Tighten the
connection and retry.
No
No
No
No
No
No
Yes
SYSTEM OK
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Light the pilot and keep the control knob pushed in
at least 10 seconds before letting go.
FLAME FAILURE FUNCTIONAL CHECK
SERVICING INSTRUCTIONS
FAULT FINDING CHARTS
IGNITION FUNCTIONAL CHECK 2
NO SPARK
Ensure there is no debris around the pilot assembly,
(e.g. coal, soot etc.) which could short the spark, clean the area.
Consult Section 2, User
Instructions, retry.
Operate the valve to light
the pilot, does the valve
'click'?
Is the pIlot burner
horizontal?
See diagram 1 on page
20**
Has ignition lead
become detached or is
connection poor?
Remove the electrode lead
from electrode with insulated
pliers. Hold the tip 4mm from the
pilot pipe work, is there a spark
when the valve ‘clicks’?
Is the electrode wire
detachable from the piezo
in the valve?
Replace the combined
lead and piezo, retry.
Correct and retry.
Check for defective or
damaged control knob spindle
or cam operation. Check for
correct location of piezo
components. Correct and retry.
Remove the electrode lead from
the piezo. Operate the valve.
Does a spark jump from the
piezo to the valve body?
Is the valve being
operated correctly?
Reset the pilot burner.
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
Replace the electrode. Replace the electrode
lead and retry.
Replace the piezo
and gas valve and retry.
Yes No
No
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco F40 Avanti Balanced Log at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco F40 Avanti Balanced Log in the language / languages: English as an attachment in your email.

The manual is 3.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info