813395

Gazco F40 Avanti Balanced Log Manual

15
Zoom out
Zoom in
Previous page
1/32
Next page
15
INSTALLATION INSTRUCTIONS
INSTALLATION
3. INSTALLATION OF THE STOVE
3.1 Remove the outer sleeve and packaging from the stove.
3.2 Open the door by pushing on the bottom right of the door
to release it.
3.3 Open the door to a 90° angle.
3.4 Lift the door off the two hinge pins on the left.
1
AR1453
3.5 To remove the glass frame unscrew the eight pozi drive
screws.
2
AR1454
Important: Make sure the stove is adjusted for the gas
type and category in its country of use. Refer to the data
badge and Technical Specification page. For details of
changing between gas types refer to Replacing Parts,
Changing Between Gas Types.
1. SAFETY PRECAUTIONS
1.1 This stove must be installed in accordance with the rules in
force. You must read these instructions before installing the
stove.
1.2 All the instructions must be left intact with the user.
1.3 In the interests of your own and other’s safety, this stove
must be installed by a competent person according to local
and national codes of practice. Failure to install the stove
correctly could lead to prosecution.
1.4 This stove is for use on a governed gas installation and set to
the required pressure.
1.5 Keep all plastic bags away from young children.
1.6 Do not place any object on or near the stove. Leave
adequate clearance above the stove (Site Requirements,
Stove Location, Diagram 7).
2. CONTROL UPGRADE
2.1 The stove is fitted with a control valve that can be upgraded
to support a battery powered remote control. Two types of
remote control can be obtained through your local Gazco
stockist:
2.2 This upgrade can be fitted before or after installation, but, if
side clearances are limited, it will be easier to upgrade the
stove before installation. Full instructions are included with
the kit.
2.3 The Standard Remote Control (Gazco Part No. 8455)
controls the gas stove after the pilot is lit so you can regulate
the main burner through its range of settings and turn the
burner off leaving just the pilot lit.
2.4 The Thermostatic and Timer Remote Control (Gazco Part
No. 8456) controls the stove after the pilot is lit using three
modes:
—Manual Mode – used to turn the burner on and off and
regulate it through its range of settings.
—Auto Mode – used to turn the burner on and off and
regulate the heat to a pre-set temperature.
—Timer Mode – used to turn the burner on and off at two
pre-set times and regulate the heat to a pre-set
temperature during those periods.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco F40 Avanti Balanced Log at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco F40 Avanti Balanced Log in the language / languages: English as an attachment in your email.

The manual is 3.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info