813395

Gazco F40 Avanti Balanced Log Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
5
2.2 Refer to separate instructions if your stove is upgraded to
include battery remote control. The following instructions
apply whether or not you have the remote upgrade.
Lighting the Pilot
2.3 The left-hand and right-hand control knobs must both point
to off (•):
AR0914
1
2.4 Press in the right-hand control knob and rotate anti-
clockwise until a click is heard.
2.5 Continue to press in. The knob should point to the pilot
(). The pilot should now light.
2.6 Keep the knob depressed for 10 seconds before
releasing. The pilot should remain lit.
2.7 If the pilot does not stay lit repeat the above steps.
NOTE: If the pilot goes out the Interlock system prevents
it being lit again for a short period.
2.8 If, after repeating the above steps, the pilot does not light,
contact your retailer or installer.
Adjusting the Flame height
2.9 Turn the right hand control to point to main burner ( ).
You can now adjust the flame height and temperature using
the left-hand control knob.
2.10 Turn the left-hand knob anti-clockwise to increase the
flame height.
2.11 Turn clockwise to decrease the height.
YELLOW FLAMES APPEAR WHEN THE STOVE HAS
REACHED SUFFICIENT HEAT (10 TO 20 MINUTES).
IF THE STOVE IS EXTINGUISHED OR GOES OUT
DURING USE WAIT 3 MINUTES BEFORE ATTEMPTING
TO RELIGHT.
3. TURNING THE STOVE OFF
3.1 To turn off main burner turn the left-hand knob until it
points to off (•). The pilot light will remain lit.
3.2 To turn off pilot light press in and turn the right-hand knob
until it points to off (•). The pilot light will go out.
4. UPGRADING THE STOVE
The stove is fitted with a control valve that can be upgraded
to support a battery powered remote control. Two types of
remote control can be obtained through your local Gazco
stockist:
4.1 The Standard Remote Control (Gazco Part No. 8455)
controls the gas stove after the pilot is lit so you can regulate
the main burner through its range of settings and turn the
burner off leaving just the pilot lit.
4.2 The Thermostatic and Timer Remote Control (Gazco Part
No. 8456) controls the stove after the pilot is lit using three
modes:
—Manual Mode – used to turn the burner on and off and
regulate it through its range of settings.
—Auto Mode – used to turn the burner on and off and
regulate the heat to a pre-set temperature.
—Timer Mode – used to turn the burner on and off at two
pre-set times and regulate the heat to a pre-set
temperature during those periods.
USER INSTRUCTIONS
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco F40 Avanti Balanced Log at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco F40 Avanti Balanced Log in the language / languages: English as an attachment in your email.

The manual is 3.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info