813476
15
Zoom out
Zoom in
Previous page
1/28
Next page
15
4. GAS SUPPLY
4.1 Having run the gas supply to the appliance, PURGE THE
SUPPLY PIPE. This is essential to expel any debris that may
block the gas controls. Connect the gas supply to the
8mm-compression elbow at the right hand rear corner of
the appliance.
AR0934
1
There is a cutout in the right hand rear leg to enable a
direct straight connection to be made to the rear of the
appliance. See Diagram 1. A gas soundness check must be
completed up to the gas inlet connection.
4.2 Check the pull of the flue system by applying a lighted
smoke pellet to the flue system opening. If there is a
definite flow into the chimney, proceed with the
installation. If not, warm the chimney for a few minutes.
IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY
REQUIRE ATTENTION - SEEK EXPERT ADVICE
4.3 The flue system may now be connected to the appliance.
Ensure that all joints are sealed with a suitable fire resistant
sealant. It is also recommended that a physical retention
method be used at the flue spigot joint, self-tapping screws
are recommended.
4.4 Connect a suitable pressure gauge to the test point located
on the inlet fitting and turn on the gas supply. Light the
appliance and check all gas joints for gas soundness. Turn
the appliance to a maximum and check that the supply
pressure is as stated on the databadge. Turn the gas off and
replace the test point screw. Turn the gas on and check the
test point for gas soundness.
5. CLOSURE PLATE INSTALLATION
NOTE: The Small & Medium stoves are also suitable for
installation into a fireplace opening. The following
method illustrates how this can be achieved with the aid
of the optional closure plate and spigot extension. Ensure
the fireplace dimensions are as shown in Diagram 2.
5.1 Place the closure plate against the fireplace opening and
ensure there is sufficient overlap around the perimeter to
allow a fume tight seal to be made. Cut straight across the
top of the plate if trimming is required.
5.2 Seal the plate to the opening and the hearth with a suitable
heat resisting material. Ensure that any relief opening at the
bottom of the plate is left unobstructed.
5.3 Secure the spigot extension to the engine assembly and seal
with heat resisting tape or similar. Position the engine
assembly ensuring 50mm rear clearance is maintained (see
Diagram 2) and then proceed with the installation as
detailed in points 3.2 to 3.3 above.
AR0377
2
6. FUEL BED ARRANGEMENT
The major ceramic components can be found inside the
firebox. Remove the cast iron door using the tool provided,
and remove all the protective packaging from these
components. See Diagram 3.
AR0540
3
NOTE: THE CAST IRON IS HEAVY, TAKE EXTREME CARE
WHEN HANDLING.
The loose coals should be arranged as specified in the
following steps. Care should be taken to ensure that there is
sufficient space between the coals to allow flames to pass
through.
INSTALLATION INSTRUCTIONS
INSTALLATION
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Clarendon - coal at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Clarendon - coal in the language / languages: English as an attachment in your email.

The manual is 3.18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info