813473

Gazco Ashdon - Conventional Flue Manual

26
Zoom out
Zoom in
Previous page
1/32
Next page
26
1. General
IMPORTANT: ALWAYS WEAR THE GLOVES
PROVIDED WHEN HANDLING AN IVORY
PAINTED APPLIANCE.
1.1 All main components can be replaced without removing the
appliance from its installation.
1.2 Ensure the appliance and surrounds are cool before servicing.
IT IS ESSENTIAL THAT THE GAS SUPPLY TO THE
APPLIANCE IS TURNED OFF AT THE ISOLATION
DEVICE BEFORE PROCEEDING FURTHER.
1.3 If, for any reason, the flue has to be removed from the
appliance, the seals must be replaced.
2. Removing the Door
IMPORTANT: THE OUTER PANELLING AND DOOR
OF THE APPLIANCE IS MADE FROM CAST IRON .
TAKE CARE WHEN INSTALLING, REMOVING AND
STORING TO AVOID DAMAGING THE OUTER
CASING, HEARTH OR DOOR.
2.1 Remove the 4 black nuts retaining the door, see Diagram 1.
Take care when removing the door as it is heavy. Place
carefully to one side.
1
2.2 Lift out the log guard and carefully remove the ceramic fuel
bed components.
2.3 Refit in reverse order.
2.4 Ensure that the rope seal on the back of the door is intact,
locate the door on the 4 studs and slide back to the firebox.
Secure in place using the 4 dome nuts and tool supplied. Do
not over tighten the nuts, see Diagram 1.
NEVER OPERATE THE APPLIANCE WHEN THE DOOR
IS REMOVED, OR THE GLASS IS BROKEN.
2.5 Replace ALL of the securing nuts ensuring that a nut is
present on all fixing studs.
UNDER NO CIRCUMSTANCES SHOULD THE
APPLIANCE BE USED IF ANY OF THE DOOR
RETAINING NUTS ARE LOOSE OR MISSING.
3. Main Burner
3.1 Turn the gas supply off at the isolation device, remove the
door and place to one side, carefully remove the ceramic
fuel bed components.
3.2 Remove the 3 securing screws, 2 at the rear and 1 at the
front left hand side, see Diagram 2.
3.3 Raise the left hand side of the burner to clear the bracket,
draw the left hand side forward.
The burner venturi is engaged over the injector. When
removing the burner be sure to clear the injector, this will
release the right hand side of the burner.
Take care when removing the burner so as not to
damage the pilot burner.
2
3.4 To replace the burner, engage the venturi over the injector
ensuring the burner sits on top of the fixing bracket. Push
the burner to the right and whilst holding, insert the three
fixing screws.
NOTE: BEFORE REPLACING THE BURNER, ENSURE
THE SILICONE SEAL AROUND THE INJECTOR IS
INTACT AND CHECK THAT VENTURI COVER IS
ATTACHED.
4. Pilot Unit
The pilot assembly consists of five components, which can
be individually changed, these are:
4a) Pilot burner bracket
4b) Pilot injector
4c) Electrode
4d) Thermocouple
4e) Gasket.
4.1 Turn the gas supply off at the isolation device, remove the
door and place to one side, carefully remove the ceramic
fuel bed components.
4.2 Remove the main burner, see Section 3.
Servicing Instructions - Replacing Parts
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Ashdon - Conventional Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Ashdon - Conventional Flue in the language / languages: English as an attachment in your email.

The manual is 2.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info