813474
24
Zoom out
Zoom in
Previous page
1/32
Next page
24
1. Servicing Requirements
IMPORTANT – The glass panel on this appliance should be
checked for any signs of damage on the front face of the
glass panel (scratches, scores, cracks or other surface
defects). If damage is observed, the glass panel must be
replaced and the appliance must not be used until a
replacement is installed. Under no circumstances should the
appliance be used if any damage is observed. Please isolate
the appliance until a replacement glass panel has been
obtained and installed. Replacement glass panels can be
purchased from Gazco via the retailer from which the
appliance was purchased or any other Gazco distributor.
This appliance must be serviced at least once a year by a
competent person.
All tests must be carried out in accordance with the current Gas
Safe recommendations.
1.1 Before Testing:
Conduct a gas soundness test for the property ensuring
there are no leaks before servicing.
Check the operation of the appliance before testing.
1.2 Special checks:
Clean the burner using a vacuum cleaner with a soft brush
attachment. Ensure all debris is removed from the burner ports.
—Clean any lint or fluff from the pilot - pay particular
attention to the aeration holes of the pilot
Clean away lint or fluff from under the burner.
Check the spark gap on the pilot is correct, see Diagram 1.
Ensure that the door is secured correctly and that all
retaining nuts are in place.
1.3 Correct any faults found during the initial test.
1.4 Re-commission the appliance in accordance with
Commissioning Procedures.
1.5 Advise the customer of any remedial work undertaken.
13mm
7 mm
1
Servicing Instructions
Servicing/Fault Finding Charts
IGNITION FUNCTIONAL CHECK 1
PILOT WILL NOT LIGHT
Ensure there is no debris around the pilot assembly,
(e.g. soot, etc.) which could short the spark, clean the area.
Operate the valve.
Is there a spark?
Consult User
Instructions and retry.
Check alignment of pilot
burner head. Change the
ignition lead. See Replacing
Parts, Section 5.
Check isolation tap and
gas meter. Retry.
Correct and retry.
Purge the gas pipes
and retry.
GO TO THE NEXT
CHART IGNITION
FUNCTIONAL CHECK 2
SYSTEM OK
There is a block in the system.
Check the inlet test point and the mag seating.
Is the gas turned on to
the appliance?
Is the gas pressure correct?
Has the system got
any air in it?
Does the pilot light?
Is the control being operated
correctly?
Will the pilot light with a
match?
No Yes
No
Yes
No
Yes
Yes
No
No
Yes
No
No
Yes
Yes
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Ashdon - Balanced Flue -Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Ashdon - Balanced Flue -Gas in the language / languages: English as an attachment in your email.

The manual is 2.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info