714637

Gastroback 40977 Manual

58
Zoom out
Zoom in
Previous page
1/65
Next page
EN EN
114 115
REMOVING AND DISASSEMBLING THE MINCER
1. Switch off the machine (press the control dial) and unplug (see above: ‘Switching
Off the Machine’).
2. Remove the tablet of the mincer. Then, gasp the mincer with your right hand
and, while holding the release button pressed with your left hand, turn the mincer
clockwise. Then pull the mincer out of the mincer coupling at the mixing arm.
3. Ensure that the mincer coupling within the mixing arm is clean and dry. If
required, wipe the mincer coupling using a soft, and only slightly damp cloth for
removing any residues of food. Then whip dry thoroughly.
4. Ensure that the mincer coupling is completely dry. If so, place the cover onto the
mincer coupling and turn the cover counter-clockwise for locking it in place.
IMPORTANT - We recommend to disassemble the mincer over a large bowl made
of metal or unbreakable plastic. DO NOT use a bowl or dish made of fragile
material (e.g. china or glass). After using the mincing tools, ensure to touch the
cross blade with care to avoid cutting your hand.
5. Unscrew the screw ring from the mincer housing.
6. Hold the outlet of the mincer housing over an unbreakable bowl and shake out
the worm shaft and used accessories. If required, press the worm shaft out of
the mincer housing by pressing on the hexagonal shaft at the coupling side of
the mincer housing.
7. Clean all used parts of the mincer immediately thereafter (see: ‘Care and Cleaning’).
SOLVING PROBLEMS
If any problems occur during operation, you will find solutions in this chapter.
Problem Reason Easy solution
Emergency stop required? Unplug the machine.
General problems
You cannot switch on the
machine, the display areas
stay dark.
The stand mixer is not
live.
Check, whether the power plug is connected correctly to
a sufficient power supply (see: ‘Technical Specifications’).
Check, whether the power outlet is live by connecting a
lamp. Is the power cord damaged? Contact your vendor.
The mixing arm is in the
upper position.
Lower the mixing arm to the operating position.
2. Unplug the machine, if you do not wish to start operation again and before
assembling or disassembling any parts or cleaning the machine.
REMOVING THE MIXING TOOLS
WARNING – Do not hold your hands or any objects (e.g. cooking utensils or
brushes) onto the mixing tools, while the machine is connected to the power sup-
ply. Do not hold your hand into the joint between the mixing arm and the back
pillar of the stand mixer to avoid crushing your hand.
IMPORTANT - Always hold the mixing arm tightly by the handle, when raising or
lowering the mixing arm. Additionally, the mixing arm is very heavy and may not
fall down from the upper position to avoid damage. Always lower the mixing arm
slowly into the operating position.
1. Switch off the motor (press the control dial) and unplug the machine. Remove the
splash guard.
2. Tightly grasp the mixing arm at the front. Then press the unlock button, while
moving the mixing arm up. Release the unlock button and ensure that the mixing
arm is engaged securely in the upper position.
3. Hold the mixing arm at its topside, while pushing the shaft of the mixing tool
upwards until you can turn the mixing tool easily clockwise (to the right).
4. Remove the mixing tool now by pulling it gently downward.
5. Repeat the steps 3 and 4, if both kneading tools have been installed.
6. Grasp the mixing bowl with both hands and turn the mixing bowl clockwise until
you can remove the mixing bowl from the base plate. Remove residues of food
sticking to the mixing tool and inner walls of the mixing bowl.
NOTE
You may use the scraper beater for scraping food off the mixing bowl.
7. Tightly hold the mixing arm by the front and press the unlock button. Ensuring
to keep your hand away from the joint of the mixing arm, lower the mixing arm
gently down until it locks into the horizontal (operating) position.
8. Clean the machine and all used accessories immediately after usage. Do not
leave food dry on the surfaces (see: ‘Care and Cleaning’).
… 58 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gastroback 40977 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gastroback 40977 in the language / languages: English, German as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info