730371
6
Zoom out
Zoom in
Previous page
1/30
Next page
Vehicle mode
Motorcycle mode
Off-road mode
Choosing a Transportation Mode
Select the transportation mode icon on the status bar.
Using the Large Button Keyboard
You can enable additional keyboard languages or layouts in the
language and keyboard settings .
Select or to view more characters.
Select to switch to other keyboard languages and layouts.
Installation
Mounting your device in a motorcycle
Powered Motorcycle Mount
WARNING
Garmin
®
strongly recommends having an experienced installer
with the proper knowledge of electrical systems install the
device. Incorrectly wiring the power cable can result in damage
to the vehicle or the battery and can cause bodily injury.
See the Important safety and product information guide in the
product box for product warnings and other important
information.
The device must be mounted in a suitable and secure location
on your motorcycle, based on available power sources and safe
cable routing. No fuse is required.
Motorcycle mount
10 to 30 Vdc system power (red)
System ground (black)
NOTE: additional parts are included with the device to provide
more installation and wiring options. Contact an experienced
installer for more information about using these parts with your
motorcycle.
Crimp-Style Ring Terminal: connects the wiring harness
directly to the battery terminal.
Cable Tie: secures cables to the motorcycle frame.
Installing the Handlebar Base
The device includes parts for two handlebar installation
solutions. Custom mounts may require additional hardware.
Installing the U-bolt and Handlebar Base
1
Place the U-bolt around the handlebar , and thread the
ends through the handlebar base .
2
Tighten the nuts to secure the base.
NOTE: the recommended torque is 50 lbf-in (5.65 N-m). Do
not exceed torque of 80 lbf-in (9.04 N-m).
Installing the Handlebar Base to the Clutch-Clamp or Brake-
Clamp Brackets
1
Remove the two factory bolts on your clutch-clamp or brake-
clamp bracket .
NOTE: both 1/4 in. (65 mm) standard and M6 bolts are
included. Match the size of the factory bolts on your clutch-
clamp or brake-clamp bracket.
2
Thread the new bolts through the handlebar base, spacers
, and clutch-clamp or brake-clamp bracket.
3
Tighten the bolts to secure the base.
Attaching the Power Cables to the Motorcycle Mount
1
Thread the power cable connector through the opening
in the motorcycle mount.
2
Pull the cable back until it is snug.
3
Screw the black screw into the back of the mount to
hold the cable in place.
NOTE: an additional replacement screw is included in the
box.
Attaching the Base Plate to the Motorcycle Mount
NOTICE
Direct, sustained contact with the base plate or any part of the
motorcycle may damage the mount over time. To prevent this
kind of damage, you must place the mounting spacers between
the mount and base plate, and make sure that no part of the
device or mount touches the motorcycle.
2 Installation
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Zumo XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Zumo XT in the language / languages: English as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Zumo XT

Garmin Zumo XT User Manual - German - 34 pages

Garmin Zumo XT User Manual - Dutch - 32 pages

Garmin Zumo XT User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info