691377
6
Zoom out
Zoom in
Previous page
1/14
Next page
2
Align the arrow on the mount with the center arrow on the
curved rail.
3
Using a 7/64 inch hex wrench, tighten the screw at the front
of the rail mount
Â
to a maximum torque specification of 2.2
N-m (20 lbf-in).
4
Align the large holes on the mount
Ã
with the mounting holes
on the side of your bow.
TIP: The mount contains three sets of mounting holes. Mount
the sight in a location that functions best with your peep sight
aperture. Mounting the sight closer to the bow may allow a
better fit in some bow cases.
5
Using a 1/8 inch hex wrench, secure the mount using the
included mounting screws
Ä
.
6
Tighten the mounting screws to a maximum torque
specification of 6.7 N-m (60 lbf-in).
NOTE: Do not exceed the bow manufacturer's recommended
torque values.
Securing the Trigger
1
Position the ranging trigger
À
on the grip of your bow where
you can comfortably activate it at full draw.
NOTE: You should confirm the trigger and the trigger cable
are positioned so they do not interfere with the operation of
the bow.
2
Secure the trigger to the bow using the included tape
Á
.
TIP: You can use the extra piece of tape to secure the trigger
cable to the riser.
Turning the Device On or Off
1
To turn on the device, press .
2
To turn off the device, hold for 3 sec.
Calibrating the Bow Sight
The first time you turn on the Xero bow sight, you are prompted
to go through initial setup steps. You can view tutorial videos at
www.garmin.com/xerotutorials.
1
Select a language.
2
Select a unit of measure.
3
Select Yes to start the pin calibration procedure.
4
Select a ranged pin color (A1i model only).
5
If necessary, select Yes to adjust the pin and rangefinder
reticle brightness and follow the on-screen instructions.
6
Set the primary pin (Setting the Primary Pin, page 2).
7
Select Done.
8
Align the rangefinder with the primary pin (Aligning the
Rangefinder with the Primary Pin, page 3).
9
Select Done.
10
Follow the on-screen instructions to complete the pin
calibration procedure and set pins for additional distances.
Torque Specifications
When adjusting and tightening the mounting screws, you should
ensure the screws are always tightened to a maximum torque
specification of 2.2 N-m (20 lbf-in.). If you do not have a torque
wrench, you can tighten the screws until the screw head makes
contact with the mount surface, then tighten the screw an
additional one quarter turn.
Setting the Primary Pin
The primary pin is a fixed point on the device optic that points
along the same axis as the laser rangefinder. You can change
the primary pin's alignment by adjusting the straight vertical and
horizontal adjustments on the mount. After you set the primary
pin, you can set additional pins for different distances using the
device software.
1
Aim at a target that is a minimum distance of 15 m (15 yd.)
away.
NOTE: If you set your primary pin for farther distances, such
as 30 m (33 yd.), you will have a farther maximum range, but
2 Calibrating the Bow Sight
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Xero A1i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Xero A1i in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Xero A1i

Garmin Xero A1i User Manual - German - 16 pages

Garmin Xero A1i User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info