691376
7
Zoom out
Zoom in
Previous page
1/14
Next page
you will decrease visibility of closer targets. If you set your
primary pin for shorter distances, you will have greater
visibility of close targets, but a shorter maximum range.
2
Nock an arrow, and draw your bow.
3
Looking through your bow's peep sight at full draw, align the
primary pin
À
with the center of the target
Á
.
4
Confirm the bubble in the level
Â
is centered between the
lines.
5
Shoot at the target, and observe the point of impact.
6
Using a 7/64 inch hex wrench, loosen the vertical
Ã
adjustment on the mount.
7
Move the vertical adjustment in the direction of the arrow's
point of impact.
8
Tighten the vertical adjustment to a maximum torque
specification of 2.2 N-m (20 lbf-in).
9
Using a 7/64 inch hex wrench, loosen the horizontal
Ä
adjustment on the mount.
10
Move the horizontal adjustment in the direction of the arrow's
point of impact.
11
Tighten the horizontal adjustment to a maximum torque
specification of 2.2 N-m (20 lbf-in).
12
Continue adjusting the mount, as needed, until the point of
aim and the point of impact are the same.
TIP: You should adjust the mount in the direction of the point
of impact. For example, if the arrow impacts low and right,
you should adjust the mount down and right. You should
always tighten the mount screws to a maximum torque
specification of 2.2 N-m (20 lbf-in) between adjustments.
Aligning the Rangefinder with the Primary
Pin
The circular rangefinder reticle indicates the direction the laser
rangefinder is pointing. For best accuracy, you must align the
circular rangefinder reticle with the primary pin.
1
Nock an arrow.
2
Bring the bow to full draw, and align the peep sight with the
sight housing ring.
3
Observe the arrows
À
on the rangefinder reticle.
The arrows indicate the direction you must move the curved
adjustments on the mount. Each arrow in the optic
corresponds with one degree of adjustment on the curved
rails.
4
Using a 7/64 inch hex wrench, adjust the curved vertical
Á
and curved horizontal
Â
adjustments on the mount in the
directions the arrows indicate. For example, if the arrows
point up and right, move the curved mount pieces up and
right.
TIP: Each mark on the curved adjustments indicates one
degree. Garmin
®
recommends moving the curved rails in
small increments as indicated by the arrows in the optic when
making adjustments.
5
Continue adjusting the mounts until the primary pin is
centered in the circle of the rangefinder reticle
Ã
at full draw.
Calibrating the Bow Sight 3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Xero A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Xero A1 in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Xero A1

Garmin Xero A1 User Manual - German - 16 pages

Garmin Xero A1 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info