Manual Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 (page 27 of 66) (English)

691431

Zoom out

Zoom in

1/66

When the end point is past the start line, the line is red. This

indicates the boat must reduce speed to avoid a penalty for

reaching the start line before the timer expires.

When the end point is on the start line, the line is white. This

indicates the boat is moving at an optimal speed to reach the

start line when the timer expires.

By default, the start line guidance window and the race timer

window appear in the Sail Racing combination screen.

Setting the Starting Line

The start line guidance window is added to the Sail Racing

combination screen by default.

From the Sail Racing combination screen, select Menu >

Start Line Guidance > Start Line.

Select an option:

• To mark the port and starboard starting line marks as you

sail past them, select Ping Marks.

• To mark the port and starboard starting line marks by

entering their coordinates, select Enter Coordinates.

• To switch the position of the port and starboard marks

after you have set them, select Swap Port & Starbd.

Marks.

Using the Starting Line Guidance

You can use the starting line guidance feature to help get you

cross the start line, at the optimal speed during a sailing race.

Mark the starting line (Setting the Starting Line, page 19).

From the Sail Racing combination screen, select Menu >

Start Line Guidance > Target Speed, and select your target

speed when crossing the starting line.

Select Target Time, and select the target time to cross the

starting line.

Select Back.

Start the racing timer (Starting the Race Timer, page 19).

Starting the Race Timer

The race timer is added to the Sail Racing combination screen

by default.

From the Sail Racing combination screen, select Start.

NOTE: You can also access this from the Sailing SmartMode

screen and the navigation chart.

When necessary, select Sync to synchronize with the official

race timer.

Stopping the Race Timer

From the Sail Racing combination screen, select Stop.

Setting the Distance between the Bow and the GPS

Antenna

You can enter the distance between the bow of your boat and

the location of your GPS antenna. This helps ensure the bow of

your boat crosses the starting line at the precise start time.

From a navigation chart, select Menu > Sailing > Start Line

> GPS Bow Offset.

Enter the distance.

Select Done.

Laylines Settings

To use the laylines features, you must connect a wind sensor to

the chartplotter.

When in sailing modeSetting the Vessel Type, page 4, you can

display laylines on the navigation chart. Laylines can be very

helpful when racing.

From the navigation chart, select Menu > Layers > My Vessel >

Laylines > Setup.

Display: Sets how the laylines and vessel appear on the chart,

and sets the length of the laylines.

Sailing Ang.: Allows you to select how the device calculates

laylines. The Actual option calculates the laylines using the

measured wind angle from the wind sensor. The Manual

option calculates the laylines using manually entered

windward and leeward angles.

Windward Ang.: Allows you to set a layline based on the

windward sailing angle.

Leeward Ang.: Allows you to set a layline based on the leeward

sailing angle.

Tide Correction: Corrects the laylines based on the tide.

Layline Filter: Filters the layline data based on the time interval

entered. For a smoother layline that filters out some of the

changes in the boat's heading or true wind angle, enter a

higher number. For laylines that display a higher sensitivity to

changes in the boat's heading or true wind angle, enter a

lower number.

Setting the Keel Offset

You can enter a keel offset to compensate the water depth

reading for the transducer installation location. This allows you

to view the depth of the water below the keel or the true depth of

the water, depending on your needs.

If you want to know the water depth below the keel or the lowest

point of your boat and the transducer is installed at the water

line or anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the boat.

If you want to know the true water depth and the transducer is

installed below the water line, measure the distance from the

bottom of the transducer up to the water line.

NOTE: This option is only available when you have valid depth

data.

Measure the distance:

• If the transducer is installed at the water line

anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the

boat. Enter this value as a positive number.

• If the transducer is installed at the bottom of the keel

and you want to know the true depth of the water,

measure the distance from the transducer to the water

line. Enter this value in as a negative number.

Select Settings > My Vessel > Depth and Anchoring >

Keel Offset.

Select if the transducer is installed at the water line, or

select if the transducer is installed at the bottom of the

keel.

Enter the distance measured in step 1.

Heading Line and Angle Markers

The heading line is an extension drawn on the map from the

bow of the boat in the direction of travel. Angle markers indicate

relative position from the heading or course over ground, which

are helpful for casting or finding reference points.

Setting the Heading Line and Angle Markers

The heading line is an extension drawn on the map from the

bow of the boat in the direction of travel. Angle markers indicate

Sailing Features 19

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 in the language / languages: English as an attachment in your email.

The manual is 6,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000

Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 User Manual - German - 74 pages

Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 User Manual - Dutch - 72 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 Manual

Product: