501981
3
Zoom out
Zoom in
Previous page
1/10
Next page
VHF 100/200 Series Radio Installation Instructions 3
Flush Mounting the VHF 100/200 Series Radio
In addition to the four included 4.2 × 25 mm, panhead mounting screws, ush mounting the VHF 100/200 series radio requires the
following tools (not included):
Phillips screwdriver
Drill and 9/64 in. (3.5 mm) drill bit for mounting holes
3/8 in. (10 mm) drill bit for a starter hole
Jigsaw
Scissors and tape
Center punch and hammer
File and sandpaper
Anti-seize lubricant (optional)
NOTE: Ensure that the surface on which you mount the VHF 100/200 series radio has sufcient open space behind it to accommodate the radio
and the connected cables. There should be at least 5 in. (127 mm) of clearance behind the case.
To ush mount the VHF 100/200 series radio:
1. Cutandtrimtheush-mounttemplate(page 9)andensureitwilltinthelocationwhereyouwanttoushmounttheVHF100/200
series radio.
2. Tapetheush-mounttemplatetothemountinglocation.
3. Use the center punch to indent the center of each of the four mounting-hole locations.
4. Use a 9/64 in. (3.5 mm) drill bit to drill the four mounting holes.
5. Use a 3/8 in. (10 mm) drill bit to drill a starter hole inside the corner of the template to
begin cutting the mounting surface.
6. Use the jigsaw to cut the mounting surface along the inside of the dashed line indicated
onthetemplate.Usealeandsandpapertorenethesizeofthehole.
7. Placetheradiointothecutouttoconrmthatthefourmountingholesarecorrectafter
reningthehole.Ifnot,markthecorrectlocationsofthefourmountingholes.Removethe
radio from the cutout.
8. Apply the gasket to the back of the VHF 100/200 series radio.
9. IfthetopandbottomsnapcoversareattachedtothefrontoftheVHF100/200seriesradio,removethem
by unsnapping the covers from the sides.
10. Place the VHF 100/200 series radio into the cutout.
11. Securely tighten the four mounting screws through the VHF 100/200 series radio into the drilled mounting holes.
Snap covers
NOTE: Stainless-steel screws may bind when screwed into berglass and overtightened. Garmin recommends applying an anti-galling, stainless,
anti-seize lubricant to the screw before using.
12. Place the snap covers over the mounting screws.
Gasket
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin VHF 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin VHF 100 in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin VHF 100

Garmin VHF 100 User Manual - English - 60 pages

Garmin VHF 100 Installation Guide - German - 10 pages

Garmin VHF 100 User Manual - German - 60 pages

Garmin VHF 100 Installation Guide - Dutch - 10 pages

Garmin VHF 100 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info