589619
9
Zoom out
Zoom in
Previous page
1/14
Next page
9Apply a layer of bike grease to the spindle.
10Insert the spindle into the cartridge.
11Wipe away any excess grease.
12Install the new washer and nut on the end of the spindle.
NOTE: The nut for the right spindle has a left-handed
(reverse) thread.
13Use the hex nut driver to tighten the nut.
WARNING
Garmin recommends torque of 7 lbf-ft. (10 N-m). Failure to
properly tighten the nut could cause the pedal to fall off
during a ride, which could result in property damage or
serious bodily injury or death.
14Install the new pedal by screwing it onto the cartridge until
there is no gap.
NOTE: The right pedal has a left-handed (reverse) thread.
15Replace the pedal pods and pedals according to the
installation instructions (Installing the Pedal Pod and Pedal).
16Rotate the crank arm to check for clearance and smooth
pedal rotation.
After you replace the pedals and cartridges, you must
recalibrate the system.
Vector Storage
If you are transporting your bicycle or not using Vector for an
extended period of time, Garmin recommends removing Vector
and storing it in the product box.
Vector Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Minimum 175 hours of riding time
NOTE: The pedal pod used on the right crank will
drain the battery faster than the left crank.
Operating
temperature range
From -4° to 122°F (from -20° to 50°C)
Water resistance IPX7
NOTICE
Do not submerge or pressure wash the
components.
Radio frequency/
protocol
2.4 GHz ANT+ wireless communications protocol
USB ANT Stick Specifications
Power source USB
Operating temperature
range
From 14° to 122°F (from -10° to 50°C)
Radio frequency/protocol 2.4 GHz ANT+ wireless communications
protocol
Transmission range Approximately 16.4 ft. (5 m)
Battery Information
Vector monitors the battery level of both pedal pods and sends
status information to your Edge device. When you receive a low
battery warning, you have approximately 10–20 hours of
operation time remaining.
Replacing the Pedal Pod Battery
WARNING
Do not use a sharp object to remove user-replaceable batteries.
Contact your local waste disposal department to properly
recycle the batteries. Perchlorate Material – special handling
may apply. Go to www.dtsc.ca.gov/hazardouswaste
/perchlorate.
NOTE: Always replace both batteries at the same time.
1Locate the circular battery cover À on the back of the pedal
pod.
2Use a coin Á to twist the cover counter-clockwise, moving
the arrow from the locked  to unlocked Ã.
3Remove the cover.
You can use a piece of tape Ä or a magnet to remove the
battery from the cover.
4Wait 30 seconds.
5Insert the new battery into the cover, observing polarity.
6Replace the cover, making sure the arrow points to
unlocked.
7Use a coin to twist the cover clockwise back into place,
making sure the arrow points to locked.
8Wait 10 seconds.
After you replace the pedal pod battery, you must set the
installation angle on your Edge (Setting the Installation Angle).
Appendix
Registering Vector
Help us better support you by completing our online registration
today.
Go to www.garmin.com/vectorowner.
Keep the original sales receipt, or a photocopy, in a safe
place.
Edge 810 and 510 Device Instructions
Pairing Vector with Your Edge 810 or 510 Device
1Bring the Edge device within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2Turn on the Edge device.
3From the home screen, select > Bike Profiles.
4Select a profile.
5Select .
6Enable the sensor, and select Search.
7Rotate the crank arm a few times.
Appendix 5
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Vector

Garmin Vector Quick start guide - English - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info