Manual Garmin Vector 2 (page 6 of 16) (English)

589621

Zoom out

Zoom in

1/16

Installing the Left Pedal and Pedal Pod

This procedure is for the Vector S system.

Apply a thin layer of grease on the pedal spindle threads

Insert the spindle into the crank arm

Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Clean all excess grease from the spindle using a clean cloth

and soapy water or isopropyl alcohol.

Place the pedal pod

on the spindle.

NOTE: You must carefully bend the cable

out of the way.

The pedal pod should be flat against the crank arm.

TIP: Power and cadence calculations are not impacted by the

orientation of the pedal pod. Garmin recommends placing the

pedal pod on the leading edge of the crank. When the crank

is in the forward position, the pedal pod should be pointing

downward.

Firmly plug the cable into the spindle.

Insert the screw

into the pedal pod, and use the 2.5 mm

hex key to tighten the screw.

Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

Installing the Right Pedal

This procedure is for the Vector S system.

Apply a thin layer of grease on the pedal spindle threads.

Insert the spindle into the crank arm.

Hand tighten the spindle.

Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Installing the Shoe Cleats

NOTE: The left and right cleats are the same.

Apply a thin layer of grease on the cleat bolt threads.

Align the cleat

, washers

, and bolts

Use a 4 mm hex key to loosely attach each bolt to the sole of

the shoe.

Adjust the cleat to the shoe in your preferred position.

This can be adjusted after a trial ride.

Tighten the cleat firmly to the shoe.

NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-

m).

Adjusting the Release Tension

NOTICE

Do not overtighten the release tension screw on the bottom of

the pedal. The release tension should be adjusted equally for

both pedals.

Use a 3 mm hex key to adjust the release tension of each

pedal.

There is a window on the back of the pedal binding that

shows the allowable range.

Paring Vector with Your Edge 1000

Before you can view Vector data on the Edge device, you must

pair the devices.

Pairing is the connecting of ANT+

wireless sensors. This

procedure contains instructions for the Edge 1000. If you have

another compatible device, see Other Compatible Devices, or

go to www.garmin.com/vectorowner.

Bring the Edge device within range (3 m) of the sensor.

NOTE: Stay 10 m away from other ANT+ sensors while

pairing.

Turn on the Edge device.

From the home screen, select > Sensors > Add Sensor >

Power.

Rotate the crank arm a few times.

Select your sensor.

When the sensor is paired with your Edge device, a message

appears, and the sensor status is Connected. You can

customize a data field to display Vector data.

Pedal Pod Status LED

Multiple green LED flashes indicate a system issue that requires

your attention.

NOTE: When the pedal pod battery is low, the status LED

flashes red, instead of green.

LED Activity Status

1 green flash every 10

seconds.

The Vector system is working properly.

2 flashes every 10 seconds. The pedal is not connected.

3 flashes every 10 seconds. The pedal pod is connected, but it

cannot communicate with the Edge

device.

4 flashes every 10 seconds. The pedal pod is searching for the

other pedal pod.

5 flashes every 10 seconds. The installation angle is not set or

cannot be detected.

6 flashes every 10 seconds. There is a hardware installation error.

7 flashes every 10 seconds. There is a software update in progress.

1 red flash every 10 seconds. The pedal pod battery is low.

Your First Ride

Before you ride with Vector for the first time, you must enter the

crank length and set the installation angle of the sensors inside

the pedals. The Vector system automatically calibrates after

each ride. You must also enter the crank length when you move

Vector to another bike.

This procedure contains instructions for the Edge 1000 device. If

you have another compatible device, see Other Compatible

Devices, or go to www.garmin.com/vectorowner.

Entering the Crank Length

The crank length is often printed on the crank arm.

2 Introduction

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector 2 in the language / languages: English as an attachment in your email.

The manual is 2,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin Vector 2 Manual

Product: