657433

Garmin Varia Smart Bike Lights Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
3
Place a rubber pad around the seat post, if necessary:
• If the seat post diameter is 27 to 28.6 mm, use the thicker
pad.
• If the seat post diameter is 30.4 to 31 mm, use the thinner
pad.
• If the seat post diameter is 31 to 31.8 mm, do not use a
rubber pad.
4
Place the seat-post connector around the rubber pad.
NOTE:
You should align the contours on the rubber pad with
the grooves on the inside of the seat-post connector.
5
Replace and tighten the screw.
NOTE: Garmin recommends a torque specification of 7 lbf-in.
(0.8 N-m). You should check the tightness of the screw
periodically.
6
Align the tabs on the back of the device with the seat-post
mount notches
Â
.
7
Press down slightly and turn the device clockwise until it
locks into place.
Installing the Multi-Location Mount
1
Select a secure location to mount the taillight where it does
not interfere with the safe operation of your bike.
NOTE: You can mount the device on your seat post, helmet,
backpack, or other location.
Garmin recommends that you
enable the deceleration indicator only when mounting the
device vertically on your seat post.
2
If necessary, select the correct rubber pad
À
for your seat
post shape.
3
Place the mount on the seat post or other mounting location.
4
Attach the mount securely using one or two bands
Á
.
NOTE:
You can use the hooks on the center of the mount
Â
if using only one band.
5
Align the tabs on the back of the device with the mount
notches
Ã
.
6
Press down slightly and turn the device clockwise until it
locks into place.
Varia
HL
Device Overview
À
Device key Select to cycle through the headlight pairing, intensity,
and pattern modes.
Hold to turn the device on and off.
Á
Status LED View device status (Bike Light Status LEDs,
page 2).
Varia
TL
Device Overview
À
Device key Select to cycle through the taillight pairing,
intensity, and pattern modes.
Hold to turn the device on and off.
Á
Status LED (visible
above the device
key)
View device status (Bike Light Status LEDs,
page 2).
Bike Light Status LEDs
LED Activity Status
Solid red An error occurred while charging.
The device shut down to prevent
overheating.
Alternating blue and
green
The device is uploading settings from
Garmin Express
™
.
Alternating blue and red An error occurred while uploading settings
from Garmin Express.
Flashing green The battery is charging.
Solid green Charging is complete.
Flashing red The battery is low.
Flashing blue The device is in smart mode and can be
controlled by a paired wireless remote.
Using the Device Key
1
Hold the device key for 1 second to turn on the device.
The first time you turn on the device, it enters smart mode.
The status LED flashes blue. The device can be controlled by
a paired wireless remote or Edge
device.
2
Select the device key to cycle through the bike light intensity
and pattern modes.
Taillight modes include smart mode, high, medium, low, and
flash. Headlight modes include smart mode, overdrive, high,
medium, low, and flash.
NOTE:
Taillight medium and flash modes are available on
the
Varia TL 300 device only. Headlight overdrive and flash
modes are available on the Varia
HL
500 device only.
3
Hold the device key for 2 seconds to turn off the device.
The next time you turn on the device, it enters the last-used
operating mode.
2 Introduction
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Varia Smart Bike Lights at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Varia Smart Bike Lights in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info