Manual Garmin TR-1 Gladiator (page 27 of 36) (English)

583791

Zoom out

Zoom in

1/36

Dockside Setup: Steps 1-9 can be done at the dock before heading for open water.

5. RPM Source Conguration. The default setting on the autopilot is set for a Single

Engine. If you have twin engines or more, you will need to change [Code 259] to match

your motor conguration. Twin engines; Press, release and light up the [Setup] LED on

the handheld, press and enter [Code 259] on the handheld. Press the [Up Arrow] TWO

(2) times which is setting the parameter to [(4) Both]. See page 22 code 259 for more

information.

6. Verify the autopilot tachometer (Tach Sensor Cable) is functioning properly. With

the engine(s) running. Press, release and light up the [Setup] LED on the handheld, and

press and light up [code 35]. Press and hold the [Select Load] GPS button and you

should see the [Up Arrow] and [Down Arrow] LED’s blink your port engine’s RPM. For

example, when the [Up Arrow] LED blinks 2 times and the [Down Arrow] LED blinks

5 times your engine is running at 2500 RPM. [Code 36] works the same way as code 35

for the starboard engine instead of the port engine. The autopilot tachometer system has a

lower limit setting of 200 RPM. If needed, adjusting [Code 267] (pulses per rev) to make

your autopilot tachometer match the tach on your dashboard.

7. Transition RPM. This is the RPM at which your boat transitions from displacement

to planing speed. [Code 348] is set to a factory default of 3000 (2 blinks of the [Up

Arrow] LED and 9 blinks of the [Down Arrow] LED +1). You should set it to your

boat’s transition RPM. (Example: Say that your planing speed is at 2500 RPM’s; With

the [Setup] LED lit, press and light [code 348], since the factory default is 3000 which is

2 blinks of the up arrow and 9 blinks of the down arrow (The value can be seen with the

[Setup] LED lit, press and hold the [Select Load] GPS , release the select load button, then

click the down arrow 5 times; that will set your transition RPM’s at 2500.) If you don’t

know what the transition RPM is, you will need to do this as part of your Sea Trial Setup.

8. Download to permanent memory the parameters you have adjusted so far. (This

must be done) With the [Setup] LED lit, press and hold the GPS [Select Load] button

- the [load] LED should illuminate on the handheld, while still holding down the [Select

Load] button, press and release the [Deckmount], on/off button quickly, then release the

[Select Load] GPS button.

9. Verify NMEA Connections: Verify that the NMEA connections for the GPS are

functioning. Turn on the GPS. With the Autopilot in [Standby], press and release

[Setup] button on the handheld. Press and light up the number 4 and the number 8

LED’s[ Code 48]. If the [up arrow] LED lights when you hold down the [Select Load]

(GPS) button, the autopilot does not acknowledge the validity of the GPS data.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin TR-1 Gladiator in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin TR-1 Gladiator Manual

Product: