583791
24
Zoom out
Zoom in
Previous page
1/36
Next page
21
22
Table of Setup Codes
HYDRAULIC CODES
Description Code Values of the Parameters Factory
Defaults
Helm Displacement 269 .1 to 6 by .1’s 1.7
Pump Displacement 169 [Up Arrow] for 4 liter, [Down Arrow] for 2 liter 2 liter
Turns Lock to Lock 26 .1 to 10 by .1’s 4.5
Sloppy Linkage Compensation 257 8 settings, 8 for most sloppy 1
Code 257: In case of sloppy and loose steering linkages, increasing this parameter may help to reduce heading
oscillations due to the linkage. Use with caution.
Shadow Drive Desensitize 368 1 most sensitive, 40 least sensitive 20
Code 368: If the shadow drive is being false tripped, i.e., autopilot is disconnected when the helm is held
still, increasing this parameter may help. False tripping is usually due to leakage of uid past the helm pump
lock valve. You may need to repair the helm valves if you cannot eliminate false trips.
Shadow Drive Enable 367 [Up Arrow] for On, [Down Arrow] for Off on
Reversed Hoses 249 [Up Arrow] for Reversed, [Down Arrow] for Normal Norm
Code 249: In case of hoses installed backwards, use this code to electronically reverse the steering direction.
TACHOMETER CODES
Description Code Values of the Parameters Factory
Defaults
RPM Source Conguration 259 1, none/ 2, Port/ 3, Starboard/ 4, Both 2
Code 259:
For single engine installations, set this code to 2 (1 blink) (and hook the blue and black wires up to your
engine tach leads).
Pulses per Revolution 267 1 to 255 by 1’s 6
Code 267:
The number of tach pulses per engine revolution is an engine specic parameter. The following settings are
a good starting point, however you need to verify them on operation. V8 engines 4 ppr (3 blinks) Most outboards 6ppr
Show Port RPM 35
Hold Down [Select Load] button: 1000’s blink on
Up Arrow 100’s blink on Down Arrow
Show Starboard RPM 36 Same As Above
Transition RPM 348 100 to 6000 by 100’s 3000
Code 348:
Set this code to the RPM’s that your boat runs when almost on plane.
Low RPM Limit 357 100 to 6000 by 100’s 500
Code 357
: If your autopilot runs well at all RPMs but is a little too active at idle, you can increase this low
limit RPM to a setting that is higher than your idle RPM to reduce autopilot rudder activity at idle.
High RPM Limit 359 100 to 6000 by 100’s 6000
Code 359:
If your autopilot runs well at all RPM’s but you would like a little stiffer heading hold at the top end,
reducing this setting to an RPM lower than your actual peak RPM will help
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin TR-1 Gladiator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin TR-1 Gladiator in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info