583791
14
Zoom out
Zoom in
Previous page
1/36
Next page
11
12
If you program the [Right Chevron] and [Left Chevron[ buttons for Step turns, when one of these buttons is
pushed, the pilot will execute a port or starboard turn. The turn will terminate when the programmed step angle
is reached. The step angles are programmable from 1 to 90 degrees. Multiple pushes of these buttons will
result in a turn through an angle equal to the sum of the angles per push. For example, if you have programmed
the pilot for 10 degree steps, ve pushes of the [Right Chevron] button will turn you 50 degrees to starboard.
180 degrees is the maximum turn sum.
Change Heading Using Step Turns
Description Code Setup Options (Parameters) Factory Setting
Step Turns (Degrees per Step) 6 10 choices/ 1, 2, 3, 4, 5, 10, 15, 30, 45, or 90
Degrees
15 degree
To change the setup options for Step Turns:
You must be in [Auto] or [STBY] mode before selection process can start
1. Press and release
the [Setup] Button. The [Setup] LED will illuminate to indicate the system is ready to
take setup commands (button pushes).
2. Select the Setup Code you want to use by pressing and releasing the button labeled 6 until the appropriate
LED is lit. (See the Codes and Setup Choices on the table below).
3. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the parameter
is adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is adjusted and is in use by
the autopilot immediately.
4. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the
parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is adjusted
and is in use by the autopilot immediately.
5. To
save the changes into permanent memory and
make the selected function into a startup
default: Press and release
the [Setup] button (the [Setup] LED should be lit), and then
press and hold
the [Select Load] button. While holding down the [Select Load] button,
press and release the [Deckmount] On/Off button quickly, then release the GPS [Select
Load] button.
To use Step Turns:
1) Press and hold
the [Setup] button.
2) Select and light up [number 4] [Step] LED on the handheld.
3) Release the [Setup] button.
4) When you are ready to initiate Step Turns, do so by pressing either the
[Right Chevron] or [Left Chevron] Button. Factory default has these set
for a 15 degree turn.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin TR-1 Gladiator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin TR-1 Gladiator in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info