691039
5
Zoom out
Zoom in
Previous page
1/30
Next page
Getting started
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Update the maps and software on your device (Map and
Software Updates, page 19).
Mount the device in your vehicle and connect it to power
(Mounting and powering the Garmin device in your vehicle,
page 1).
Acquire GPS signals (Acquiring GPS signals, page 1).
Adjust the volume (Adjusting the volume, page 2) and
display brightness (Adjusting the screen brightness,
page 2).
Set up a vehicle profile for your camper (Adding a vehicle
profile, page 2).
Navigate to your destination (Starting a route, page 8).
Garmin
®
device overview
power key
USB power and data port
Map and data memory card slot
Microphone for voice command or hands-free calling
Mounting and powering the Garmin device in
your vehicle
WARNING
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Before you use your device on battery power, you should charge
it.
1
Plug the vehicle power cable into the USB port on the
device.
2
Press the mount onto the suction cup until it snaps into
place.
3
Press the suction cup to the windscreen, and flip the lever
back toward the windscreen.
4
Fit the tab on the top of the mount into the slot on the back of
the device.
5
Press the bottom of the mount into the device until it clicks.
6
Plug the other end of the vehicle power cable into a power
outlet in your vehicle.
Turning the device on or off
To turn the device on, press the power key or connect the
device to power.
To put the device in power saving mode, press the power key
while the device is on.
While in power saving mode, the screen is off and the device
uses very little power, but it can wake instantly for use.
TIP: you can charge your device faster by putting it in power
saving mode while charging the battery.
To turn off the device completely, hold the power key until a
prompt appears on the screen, then select Off.
The prompt appears after five seconds. If you release the
power key before the prompt appears, the device enters
power saving mode.
Acquiring GPS signals
When you turn on your navigation device, the GPS receiver
must collect satellite data and establish the current location. The
time required to acquire satellite signals varies based on several
factors, including how far you are from the location where you
last used your navigation device, whether you have a clear view
of the sky, and how long it has been since you last used your
navigation device. The first time you turn on your navigation
device, it may take several minutes to acquire satellite signals.
1
Turn on the device.
2
Wait while the device locates satellites.
3
If necessary, go to an open area away from tall buildings and
trees.
in the status bar indicates the satellite signal strength. When
at least half of the bars are filled, the device is ready for
navigation.
Status bar icons
The status bar is located at the top of the main menu. The status
bar icons display information about features on the device. You
can select some icons to change settings or view additional
information.
GPS signal status. Hold to view GPS accuracy and acquired
satellite information (Viewing GPS signal status, page 22).
Bluetooth
®
technology status. Select to view the Bluetooth
settings (Wireless network settings, page 18).
Wi-Fi signal strength. Select to change the Wi-Fi settings
(Wireless network settings, page 18).
Connected to hands-free calling. Select to place a phone call
(Hands-free calling, page 14).
Active vehicle profile. Select to view the vehicle profile settings
(Editing a vehicle profile, page 2).
Current time. Select to set the time (Setting the Time,
page 19).
Battery charge level.
Getting started 1
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Tourer Two at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Tourer Two in the language / languages: English as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Tourer Two

Garmin Tourer Two User Manual - German - 32 pages

Garmin Tourer Two User Manual - Dutch - 32 pages

Garmin Tourer Two User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info