657480
9
Zoom out
Zoom in
Previous page
1/16
Next page
option provides a good balance between a quickly
scrolling image and targets that are less distorted.
Setting the Bottom Search Limit
You can set a maximum depth at which the auto range feature
searches for the bottom. A lower limit acquires data about the
bottom faster than a higher limit.
1
From a sonar screen, select > Sonar Setup > Bottom
Search Limit.
2
Select a range.
Sonar Appearance Settings
From a sonar view, select > Sonar Setup > Appearance.
Color Scheme: Sets the color scheme.
Edge: Highlights the strongest signal from the bottom to help
define the hardness or softness of the signal.
A-Scope: Displays a vertical flasher along the right side of the
screen that shows instantaneously the range to targets along
a scale.
Fish Symbols: Sets how the sonar interprets suspended
targets.
Turning on the A-Scope
The a-scope is a vertical flasher along the right side of the full-
screen sonar view. This feature expands the most recently
received sonar data so that it is easier to see. It can also be
helpful for detecting fish that are close to the bottom.
NOTE: This feature is not available on all sonar screens.
From the full screen page, select > Sonar Setup >
Appearance > A-Scope.
À
A-Scope
Á
Diameter of the sonar cone at the present depth
Configuring the Appearance of Suspended Targets
NOTE: Configuring the appearance of suspended targets on
one screen applies that setting to all screens.
NOTE: This feature is not available on all sonar views.
Shows suspended targets as symbols.
Shows suspended targets as symbols with target depth
information.
Shows suspended targets as symbols with background sonar
information.
Shows suspended targets as symbols with background sonar
information and target depth information.
1
From a sonar screen, select > Sonar Setup >
Appearance > Fish Symbols.
2
Select an option.
Sonar Noise Rejection Settings
From a sonar view, select > Sonar Setup > Noise Reject.
Interference: Adjusts the sensitivity to reduce the effects of
interference from nearby sources of noise.
When you adjust the interference setting from off
À
through
low
Á
, medium
Â
, and high
Ã
, noise is gradually removed,
but there is little effect on the strong target returns. You
should use the lowest interference setting that achieves the
desired improvement to remove interference from the screen.
Correcting installation issues that cause noise is the best way
to eliminate interference.
Surface Noise: Hides sonar returns near the surface of the
water. Hiding surface noise helps reduce screen clutter.
Surface noise
À
is caused by interference between the
transducer and water. You can hide surface noise
Á
to help
reduce clutter. Wider beam widths (lower frequencies) can
show more targets, but can generate more surface noise.
TVG: Reduces surface noise.
This control is best used for situations when you want to
control and suppress clutter or noise near the water surface.
It also allows for the display of targets near the surface that
are otherwise hidden or masked by surface noise.
Overlay Number Settings
You can customize the data shown on the sonar screen.
NOTE: Not all features are available on all devices.
From a sonar screen, select > Overlay Numbers.
Navigation Inset: Shows the navigation inset when the vessel
is navigating to a destination.
Device Voltage: Shows the voltage of the device.
Speed: Shows the vessel's current speed.
Time of Day: Shows the current time of day.
Compass Tape: Shows the compass tape data bar.
Depth: Shows the transducer's current depth.
Water Temp.: Shows the current water temperature.
Waypoints
Waypoints are locations you record and store in the device.
Marking Your Present Location as a
Waypoint
From any screen, select .
Waypoints 5
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Striker 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Striker 7 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Striker 7

Garmin Striker 7 User Manual - German - 16 pages

Garmin Striker 7 User Manual - Dutch - 16 pages

Garmin Striker 7 User Manual - French - 16 pages

Garmin Striker 7 Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info