801381
18
Zoom out
Zoom in
Previous page
1/26
Next page
10 Insert the inner seal into the pedal body.
You should press it down so it is flush with the bearing.
11 Slide the outer seal on to the spindle.
12 Apply bike grease to the bearing inside the pedal body.
13 Apply a layer of bike grease to the spindle.
14 Insert the spindle into the pedal body.
The outer seal and the top of the spindle should be flush with the pedal body cartridge.
15 Replace the spindle nut.
16 While securely holding the wrench flats with a pedal wrench, use the 12 mm socket wrench to torque the
spindle nut to 7 lbf-ft. (10 N-m).
WARNING
To ensure that the spindle nut stays in place, you must tighten it to the recommended torque specification.
Failure to properly tighten the nut could cause the pedal to fall off during a ride, which could result in property
damage or serious bodily injury or death.
17 Replace the battery carriage and two screws.
18 Replace the battery and battery cover, and hand tighten it.
NOTE: Do not damage or lose the O-ring gasket.
19 Use a 4 mm hex key to tighten the battery cover to 3.6 lbf-ft. (5 N-m).
The LED displays one short green flash followed by one long red flash.
20 Install the pedals on your bike (Installing the Pedals, page2).
Rally Storage
If you are transporting your bicycle or not using Rally for an extended period of time, Garmin recommends
removing Rally and storing it in the product box.
Other Compatible Devices
Edge 530 Instructions
Pairing Rally with the Edge 530
1Bring the Edge device within 3m (10ft.) of the sensor.
NOTE: Stay 10m (33ft.) away from other riders' sensors while pairing.
2Select Menu > Settings > Sensors > Add Sensor.
3Rotate the pedals a few times in order to activate the Rally system.
4Select your sensor.
5Select Add Sensor.
When the sensor is paired with your device, the sensor status is Connected. You can customize a data field
to display power data.
Entering the Crank Length with the Edge 530
The crank length is often printed on the crank arm.
1Rotate the pedals a few times in order to activate the Rally system.
2Select Menu > Settings > Sensors.
3Select your sensor.
4Select Sensor Details > Crank Length.
5Enter the crank length, and select .
14 Other Compatible Devices
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin RS 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin RS 200 in the language / languages: English as an attachment in your email.

The manual is 3.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin RS 200

Garmin RS 200 User Manual - German - 28 pages

Garmin RS 200 User Manual - Dutch - 28 pages

Garmin RS 200 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info