657471
7
Zoom out
Zoom in
Previous page
1/10
Next page
4
Grip the rotary switch connector wires close to the connector,
and pull the connector perpendicular to the circuit board to
disconnect the rotary switch connector from the device.
5
Remove the two screws from the battery plate.
6
Lift up the battery plate.
7
Remove the old battery from the back plate, noting the
orientation of the battery.
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
8
Install the new battery into the back plate with the label side
up, using the same orientation as the old battery.
The battery orientation is noted graphically inside the back
plate.
9
Replace the battery plate to its original position.
10
Replace and tighten the battery plate screws.
11
With the new battery, connect the battery connector to the
device.
When properly installed, the connector plug snaps into the
port.
12
Reconnect the rotary switch connector to the device.
When properly installed, the connector plug snaps into the
port.
13
Verify the gasket is not damaged and is completely seated in
the groove on the front half of the device.
14
While ensuring the battery and rotary switch wires are not
pinched, hold the back plate and the device firmly together,
and replace all eight security screws without tightening.
15
Verify the back plate and the device are aligned with no
gaps.
16
Tighten the screws evenly.
17
Verify the gasket is not sticking out of the device.
Pro Trashbreaker Dog Collar Device Components
À
Security screws
Á
Top plate
Â
Battery plate screws
Ã
Battery plate
Ä
Battery
Å
Gasket
Æ
Front enclosure
Replacing the Battery Assembly
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You also need a small Phillips
screwdriver and the security screwdriver included with the
battery replacement kit.
You can purchase a replacement battery at
http://buy.garmin.com. You should use only an official Garmin
replacement part.
1
Remove the three screws
À
from the cover
Á
over the VHF
antenna
Â
.
2
Pry off the cover.
3
Remove the screw securing the VHF antenna to the back
plate.
4
Remove the six screws from the top plate, and remove the
top plate.
5
Remove the two screws from the battery plate, and remove
the battery plate.
6
Grip the battery connector wires close to the connector, and
pull the connector perpendicular to the circuit board to
disconnect the battery connector from the device.
7
Remove the battery.
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
8
Install the new battery into the front enclosure with the label
side of the battery facing up, and the lead edge of the battery
placed under the contact ledge of the device.
9
Replace the battery plate, and replace and tighten the two
screws.
10
Verify the gasket is not damaged and is completely seated in
the groove.
11
With the new battery, connect the battery connector to the
device.
Device Information 5
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Pro Trashbreaker at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Pro Trashbreaker in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info