657470
11
Zoom out
Zoom in
Previous page
1/14
Next page
PRO Control
2 Receiver Components
À
Security screws
Á
Battery connector
Â
Receiver housing
Ã
Screws for battery plate
Ä
Battery plate
Å
Battery
Replacing the PRO Control
2 Receiver Battery
Before you replace the battery, you must remove all dirt, water,
and debris from the device.
You can purchase a replacement battery at
(
http://buy.garmin.com)
. You should use only an official Garmin
replacement part.
1
Remove the eight security screws from the back of the
device.
2
Lift up the receiver housing.
3
Press down firmly on the release tab for the battery
connector, and disconnect the battery connector from the
device.
4
Remove the screws from the battery plate, and remove the
plate.
5
Remove the old battery, noting the orientation of the battery.
The battery fits tightly. You may pry the battery out of the
back plate using a non-sharp, non-metal object.
6
Install the new battery with the label side up, using the same
orientation as the old battery.
7
Replace the battery plate, and replace its screws.
8
Verify that the gasket is not damaged and is completely
seated in the groove in the receiver housing.
9
Connect the battery connector to the device.
10
Hold the bottom plate and the device firmly together, and
replace all eight security screws without tightening.
11
Verify the bottom plate and the device are aligned with no
gaps.
12
Tighten the screws evenly.
Updating the Receiver Software
1
Connect your device to a computer using the USB cable
(Connecting the Device to Your Computer, page 7).
2
Go to garmin.com/express.
3
Follow the on-screen instructions.
Connecting the Device to Your Computer
NOTICE
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to
a computer.
1
Pull up the weather cap from the USB port on the device.
2
Plug the small end of the USB cable into the USB port on the
device.
3
Plug the large end of the USB cable into a computer USB
port.
Your device appears as a removable drive in My Computer
on
Windows
®
computers and as a mounted volume on Mac
®
computers.
Downloading a Custom Sound
Before you can download a custom sound from your computer
to your receiver, your sound file must be in the proper audio
format
(
Custom Sound File Requirements, page 7).
1
Name the custom sound file to associate it with a color.
Color Filename
Blue (left) 1.wav
Black (middle) 2.wav
Red (right) 3.wav
2
Connect the receiver to your computer (Connecting the
Device to Your Computer, page 7)
.
Depending on your computer operating system, the device
appears as either a portable device, a removable drive, or a
removable volume.
3
On your computer, browse to the custom sound file location.
4
Copy the custom sound file to the GARMIN/WAV folder on
your receiver.
When you select the receiver sound (Selecting the PRO Control
2 Receiver Sound, page 3)
, the custom sound plays.
Custom Sound File Requirements
Audio file format Waveform (.wav)
Channels Mono or stereo
Resolution 16-bit
Sample rate 32 kHz
Maximum duration 50 sec. for mono for all three sounds
25 sec. for stereo for all three sounds
Resetting the Receiver to Factory Defaults
A factory reset unpairs the receiver, erases sounds stored on
the receiver, and restores the original factory sounds.
1
Connect the receiver to the computer or charger (Connecting
the Device to Your Computer,
page
7)
.
2
Hold the power key for 15 seconds until the LED is solid
yellow.
Factory reset is complete when the LED turns off.
Device Maintenance 7
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin PRO Control 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin PRO Control 2 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info